P.09
P.10
Installation Requirements
Installation Requirements
1.A120v.60Hz,AConly,15-or 20amp,fused electrical supply is required. A time-delay fuse or
circuit serving only this appliance be provided .
2.This washer is equipped with a power supply cord having a 3 prong grounding plug.
3.To minimize possible shock hazard ,the cord must be plugged into a mating,3 prong,
grounding type outlet ,grounded in accordance with local codes and
ordinances. If a mating outlet is not available ,it is the personal responsibility and obligation
of the customer to have the properly grounded outlet installed by a qualified electrician.
4.If codes permit and a separate ground wire is used ,it is recommended that a qualified
electrician determine that the ground path is adequate.
5.Do not ground to a gas pipe .
6.Check with a qualified electrician if you are not sure the washer is properly grounded.
7.Do not have a fuse in the neutral or ground circuit.
8.Certain internal parts are intentionally not grounded and may present a risk of electric shock
only during servicing. Service Personnel – Do not contact the following parts while the appliance
is energized:Electrical value,Drain Pump,Door Lock,Dry Heater(Combo),Fan Motor(Combo).
Location requirements
Selecting the proper location for your washer improves performance and minimizes noise
and possible washer
“
walk.
”
Your washer can be installed under a custom counter,or in a
basement, laundry room, closet, or recessed area. See
“
Drain System.
”
Companion
appliance location requirements should also be considered. Proper installation is your
responsibility.
You will need
1. A water heater must supply hot water with a temp of at least 120
°
F
(
49
°
C
)
water to
the washer
.
2. A grounded electrical outlet located within 6 ft.
(
1.8 m
)
of where the power cord is
attached to the back of the washer.See
“
Electrical Requirements.
”
3. Hot and cold water faucets located within 3 ft.
(
0.9 m)of the hot and cold water fill valves.
4. The
water
pressure
should
be
between
20
-
100psi
(
138
-
690kPa
)
5. A level floor with a maximum slope of 1" (25 mm)under entire washer.Installing the washer
on soft floor surfaces,such as carpets or surfaces with foam backing.is not recommended
.
6. The washer must be installed on a solid floor to minimize vibration during the spin cycle
.
7. Do not operate your washer in temperatures below
32
°
F
(
0
°
C
)
.Some water can
remain in the washer and can cause damage in low temperatures.
Installation clearances
1
.
The location must be large enough to allow the washer door to be fully opened.
°
2. Additional spacing should be considered for ease of installation and servicing. The door
opens more than 90
,and is not reversible.
3. Additional clearances might be required for wall ,door , and floor moldings.
4. Additional spacing of 25mm on all sides of the washer is recommended to reduce noise
transfer.
5. Companion appliance spacing should also be considered.
Electrical requirements
WARNING
Electrical Shock Harzard
Connect to grounded 3 prong outlet with an individual 12 amp
branch circuit protected by a 12 amp circuit breaker.
Connect to individual branch circuit.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in electrical
shock, fire, or death.
Electrical requirements
Washer dimensions
The dimensions shown are for the recommended spacing. Custom dercounter installation
23 "
( 595
mm
)
1"
(25
mm
)
1"
(25
mm
)
2" (50
mm
)
"
min
.
(850
mm
)
1
/
2
1
/
2
1
/
2
42
"
(10
80
mm
)
1
/
2
23
"
(595
mm
)
33
33
"
(850
mm
)
Unpacking the washing machine
Unpack your washing machine and check if damaged occured during the transportation.
Also make sure that all the items (as shown in Page 5) are in the attached bag.
If there is any damage to the washing machine during the transportation, or anyitem is
missing, please contact your local dealer immediately.
1
/
2
1
/
2
23
"
(595
mm
)
Summary of Contents for COMBI-110
Page 18: ......
