background image

Pick-up Device:

768 (H) x 494 (V) pixels, Interline Transfer CCD

Scanning Area:

4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of
1/3” pick-up tube)

Scanning:

525 lines/60 fields/30 frames

Horizontal:

15.734 kHz

Vertical:

59.94 Hz

Synchronization:

Internal, Line-locked or Multiplexed vertical drive (VD2)
Sync selectable

Video Output:

1.0 V[p-p] NTSC composite 75 

/BNC connector

Horizontal Resolution:

480 lines (C/L), 570 lines (B/W)

Signal-to-Noise Ratio:

50 dB (Equivalent to AGC Off, weight On, AP On)

Dynamic Range:

46 dB (Typ)

Minimum Illumination:

2.4 lx (0.24 footcandle) (WIDE) (C/L),
0.3 lx (0.03 footcandle) (WIDE) (B/W)
When the optional WV-CW1C dome cover is installed.
0.8 lx (0.08 footcandle) (WIDE) (C/L),
0.1 lx (0.01 footcandle) (WIDE) (B/W)

Gain Control:

ON (DNR-H), ON (DNR-L) or OFF (SET UP MENU) 
selectable

White Balance:

ATW1, ATW2 or AWC (SET UP MENU) selectable

Aperture:

Set Variable (SET UP MENU)

Super Dynamic

2

:

ON or OFF (SET UP MENU) selectable

Electronic Shutter Speed:

OFF, 1/100, 1/250, 1/500, 1/1 000,1/2 000,
1/4 000, 1/10 000 s selectable

Lens

Focal length:

3.8 mm - 8 mm

Maximum aperture ratio:

1:1.4 (Wide), 1:1.8 (Tele)

Angular field of view:

Horizontal: 35.6 ˚ - 73.6 ˚
Vertical:

26.6 ˚ - 53.4 ˚

Focusing range:

1.2 m - 

(3.9 ft - 

)

Ambient Operating Temperature:

–10 °C - +50 °C (14 °F - 122 °F)

Ambient Operating Humidity:

Less than 90 %

Power Source and

Power Consumption:

24 V AC 60 Hz, 4.6 W

Dimensions (without lens):

WV-CW474F:

133 mm (H) x 152.5 mm (D)
5-1/4” (H) x 6” (D)

WV-CW474S:

136.5 mm (H) x 160 mm (D)
5-3/8” (H) x 6-5/16” (D)

Weights:

WV-CW474F:

1.0 k

g

(2.2 lbs.)

WV-CW474S:

1.4 k

g

(3.1 lbs.)

Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.

SPECIFICATIONS

OPTIONAL ACCESSORIES

STANDARD ACCESSORIES

Tamperproof screw bit  ...................................................................... 1 pc.
Camera mounting bracket (supplied with only WV-CW474S)............ 1 pc.
Camera mounting screw (with a plastic washer)  .............................. 4 pcs.

(supplied with only WV-CW474S)

WV-CW1C Dome Cover
WV-Q112 Camera mounting bracket (for WV-CW474F)

2001     © Matsushita Communication Industrial Co., Ltd.

Panasonic Security and Digital Imaging Company

A Division of Matsushita Electric Corporation of America

Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094

Regional Offices:

Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303

Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838

Midwest:

1707 North Randall Road, Elgin, IL 60123 (847) 468-5211

Western:

6550 Katella Ave., Cypress, CA 90630 (714) 373-7840

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010

Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.

Ave. 65 de Infanteria. Km. 9.5
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985 (809)750-4300

Summary of Contents for WVCW474F - COLOR CCTV CAMERA











Reviews: