![background image](http://html.mh-extra.com/html/panasonic/wvcw474f-color-cctv-camera/wvcw474f-color-cctv-camera_operating-instructions-manual_1512012004.webp)
1. CAMERA SETUP MENU
This camera utilizes an on-screen user setup menu.
• Opening the Setup Menu
Press and hold down
I
(S) for 2 seconds
or more.
The CAM SET UP menu appears on the
monitor as shown at right.
Check the current settings on the menu.
Refer to the following sections for a detailed description of menu items. If you decide not to
make any changes after checking the current settings, move the cursor to END in the bot-
tom line, and press
I
(S) to close the setup menu.
Note:
If no button is pressed for 6 minutes while a setup menu is being displayed on the
monitor screen, it is automatically closed and the mode returns to the normal camera
picture.
2. SETUP OPERATION
This camera utilizes an on-screen user setup menu (CAM SET UP). To set items on the CAM
SET UP menu, use the following buttons on the side panel.
Left Button
(
I
) (L)
:
Moves the cursor to the left. Use this button to select or adjust the
parameters of the selected item. The parameter changes each
time this button is pressed.
Right Button
(
I
) (R)
: Moves the cursor to the right. Use this button to select or adjust the
parameters of the selected item. The parameter changes each
time this button is pressed.
Up Button
(
I
) (U)
:
Moves the cursor upwards. Use this button to select an item or
adjust the parameters.
Down Button
(
I
) (D)
: Moves the cursor downwards. Use this button to select an item or
adjust the parameters.
Set Button
(
I
) (S)
:
Executes selections and displays a submenu for an item with the
mark.
• To reset the parameter to the factory default setting, move the cursor to the parameter
to be reset and press
I
(L) and
I
(R) simultaneously.
• To return to the previous menu or page, move the cursor to RET and press
I
(S).
• To close the setup menu, move the cursor to END and press
I
(S).
• All Reset Operation
All Reset allows you to reset all setup menu items to the factory default settings if you are
unsure about the correct settings. Proceed as follows:
(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).
(2) While pressing both
I
(L) and
I
(R), press
I
(S) for a few seconds. The message
ALL RESET momentarily appears on the monitor screen.
This resets all adjustments and parameters to the factory default settings.
• Editing the CAM SET UP Menu
Important Notice:
When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you can-
not change the currently active settings. This is to prevent accidental changing of the
settings.
To edit the CAM SET UP menu (change
settings), press
I
(U) and
I
(D) or
I
(L) and
I
(R) to move the cursor to
SET UP DISABLE in the bottom line.
Press
I
(S). SETUP DISABLE changes
to SETUP ENABLE. Move the cursor to
DIP SW. Press
I
(S). DIP SW changes
to MENU. Then move the cursor to the
item(s) you want to change.
Notes:
• When DIP SW is selected for CAM SET UP menu, five modes can be set with the DIP
switches.
• To operate the camera functions with the system controller, select MENU in the CAM
SET UP menu.
Important Notice:
When the setup menu is closed after changing the parameters in the menu, the new
values are stored in the EEPROM (Electrically Erasable and Programmable Read-Only
Memory). These values remain valid until new values are stored, even if the power of
the camera is off.
↵
** CAM SET UP **
CAMERA ID OFF
ALC ALC
SHUTTER ---
AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF
DIP SW
END SET UP DISABLE
↵
↵
↵
** CAM SET UP **
CAMERA ID OFF
ALC ALC
SHUTTER ---
AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF
MENU
END SET UP ENABLE
↵
↵
↵
SETUP
↵
↵
↵
** CAM SET UP **
CAMERA ID OFF
ALC ALC
SHUTTER ---
AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF
DIP SW
END SET UP DISABLE