background image

1. The following functions are built in.

(1) Auto Light Control (ALC)
(2) The SUPER-D

2

function eliminates interference by strong background lighting

which makes the camera picture dark, such as a spotlight.
Dynamic range of 46 dB (Typ)

(3) Internal, Line-Locked, Multiplexed Vertical Drive (VD2) Sync
(4) Auto/Manual White Balance Function
(5) Electronic Shutter Function

2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off)
3. Minimum illumination of 2.4 lx (0.24 footcandle) (WIDE) (Color mode)

Minimum illumination of 0.3 lx (0.03 footcandle) (WIDE) (Black-and-white mode)
Minimum illumination of 0.8 lx (0.08 footcandle) (WIDE) with the WV-CW1C optional
dome cover (Color mode)
Minimum illumination of 0.1 lx (0.01 footcandle) (WIDE) with the WV-CW1C optional
dome cover (Black-and-white )

4. 480 lines of horizontal resolution (Color mode)

570 lines of horizontal resolution (Black-and-white mode)

5. High quality picture:

(a) 2H type vertical enhancer for greater picture sharpness

(b) Chroma averaging circuit for better color signal-to-noise ratio

(c) Minimum of aliasing on fine objects

(d) Expanded dynamic range by use of knee circuit

(e) Highlight aperture correction for greater picture detail of bright objects

6. Selectable electronic sensitivity enhancing modes including AUTO, MANUAL and OFF
7. Built-in Digital Motion Detector
8. Auto black-and-white mode enables the camera to switch between color and black-and-

white picture in response to Light input.

9. Electronic zoom function magnifies a scene 2-fold and changes the angle of view.

FEATURES

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

q

Panning table

Adjusts the panning angle of the camera.

w

Pan lock screw

Fixes the panning position.

e

Tilting lock screw

Fixes the tilting position.

r

AZIMUTH (Angle adjuster)

Shoots in a straight-angle field of view when aiming at an object in a slanting direction
even if the tilt angle has been set.

t

Zoom lock lever

Fixes the zoom position.

y

Focus lock lever

Fixes the focus position.

u

LEFT button (

I

) (L)

Moves the cursor to the left, selects the mode and adjusts some levels.

q

w

e

r

y

t

u

i

o

!0

!1

!2

!3

!4

!5

!6

!7

LOW

HIGH

OFF

AUTO1

SHARP

SOFT

OFF

ON

INT

LL

L

EFT

U

P

D

OWN

SET

R

  IGHT

Summary of Contents for WVCW474F - COLOR CCTV CAMERA











Reviews: