manualshive.com logo in svg

Panasonic WV-NW502S, Installation Manual, Page: 41 / 44

Share
Download
Panasonic WV-NW502S Installation Manual Download Page 41

41

Compatible SDHC/SD memory 
card (option):

Manufactured by Panasonic
SDHC memory card: 4 GB, 8 GB, 16 GB, 32 GB
SD memory card: 64 MB, 128 MB, 256 MB, 512 MB, 
1 GB, 2 GB
(except miniSD card and microSD card) 

*1 When the camera is installed and operated in low temperatures below –10 °C {14 °F}, nor-

mal images may not be obtained immediately after startup. In such a case, wait until the
camera warms up (taking approx. more than 1 hour) and perform adjustment after turning
on the power again.

*2 Either H.264 or MPEG-4 is selectable. 
*3 Transmission for 2 streams can be individually set in the same compression method. 
*4 Constraints are imposed when using Microsoft

®

Windows Vista

®

. Refer to "Notes on

Windows Vista

®

" (PDF) for further information about system requirements for a PC and pre-

cautions when using Microsoft

®

Windows Vista

®

.

*5 When using IPv6 for communication, use Microsoft

®

Windows Vista

®

exclusively. 

Summary of Contents for WV-NW502S













































Reviews:

No comments