Panasonic WV-NW502S Installation Manual Download | Manualshive

Page: 36 / 44

background image

36

z

Start the Panasonic IP setting software.

x

Click the [IP setting] button after selecting the
MAC address/IP address of the camera to be
configured.

Note:

• When using a DHCP server, the IP address

assigned to the camera can be displayed by
clicking the [Refresh] button of the IP setting
software.

• When a duplicate IP address is used, the cor-

responding MAC address/IP address will be
displayed shaded.

c

Complete each network setup item and click
the [Apply] button.

Note:

• When using a DHCP server, it is possible to

set "DNS" to "AUTO".

Important:

• It may take for around 2 minutes to complete to upload the settings to the camera after

clicking the [Apply] button. The settings may be invalidated when the 12 V DC power sup-
ply is cut or when the LAN cable is disconnected before completing the upload.In this
case, perform the settings again.

• When using a firewall (including software), allow access to all UDP ports.

«
...
34
35
36
37
38
...
»

Summary of Contents for WV-NW502S













































Reviews:

No comments

Related manuals for WV-NW502S

PowerShot SX210 IS

Brand: Canon Pages: 180

PowerShot SD430 DIGITAL ELPH WIRELESS

Brand: Canon Pages: 7

PowerShot SD630 Digital ELPH Camera

Brand: Canon Pages: 137

Brand: Canon Pages: 2

Brand: Papago Pages: 82

Brand: V-TAC Pages: 97

Brand: V-TAC Pages: 14

Brand: Canon Pages: 83

Brand: D-MAX Pages: 8

Brand: Ken A Vision Pages: 2

Brand: Acebil Pages: 11

Brand: QHYCCD Pages: 16

Brand: ViziT Pages: 2

VK2-3MPBIR28V12re

Brand: Vista Pages: 14

Brand: Manfrotto Pages: 2

Brand: Silent Witness Pages: 26

NG-IPCAMEV8180A

Brand: Net Generation Pages: 33

PanoMachine MultiRowPlan

Brand: MK Panorama Systeme Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands