background image

10

ENGLISH

CHARGING AND DISCHARGING 

THE WATER

5

 

Make sure all the piping installations are properly done before 
carry out below steps.

CHARGE THE WATER

For Domestic Hot Water Tank

1.  Set the Domestic Hot Water Tank Discharge (Drain Tap) 

g

 to 

“CLOSE”.

“CLOSE”

“OPEN”

Domestic Hot Water Tank Discharge (Drain Tap) 

g

2.  Set all Tap / Shower “OPEN”.
3.  Start fi lling water to the Domestic Hot Water Tank via Tube 

Connector 

i

After 20~40min, water should fl ow out from Tap / Shower.
Else, please contact your local authorized dealer.

4.  Check and make sure no water leaking at the tube connecting 

points.

For Space Heating / Cooling

1.  Turn the plug on the Air Purge Valve 

a

 outlet anticlockwise by 

one complete turn from fully closed position.

Air purge valve 

a

Plug (turn 
anticlockwise by 
one complete turn)

2.  Set the Pressure Relief Valve 

b

 lever “DOWN”. 

Pressure relief valve 

Pressure relief valve 

b

Lever

Turn down

or

Pressure relief valve 

b

Lever

Turn down

Pressure relief valve 

b

3.  Start fi lling water (with pressure more than 0.1 MPa (1 bar)) to the 

Space Heating / Cooling circuit via Tube Connector 

g

. Stop fi lling 

water if the free water fl ow through Pressure Relief Valve Drainage 

h

.

4.  Turn ON the Tank Unit and make sure Water Pump 

2

 is running.

5.  Check and make sure no water leaking at the tube connecting points.

DISCHARGE THE WATER

For Domestic Hot Water Tank 

1.  Turn OFF power supply.
2.  Set the Domestic Hot Water Tank Discharge (Drain Tap) 

g

 to “OPEN”.

3.  Open Tap / Shower to allow air inlet.
4.  After discharge, set Domestic Hot Water Tank Discharge (Drain 

Tap) 

g

 to “CLOSE”.

RECONFIRMATION

6

 

WARNING

Be sure to switch off all power supply before performing each of 
the below checkings.

CHECK WATER PRESSURE

 

*(0.1 MPa = 1 bar)

Water pressure should not lower than 0.05 MPa (with inspects the 
Water Pressure Gauge 

d

). If necessary add water into Tank Unit 

(via Tube Connector 

g

).

CHECK PRESSURE RELIEF VALVE 

b

 

Check for correct operation of Pressure Relief Valve 

b

 by turning 

on the lever to become horizontal.

 

If you do not hear a clacking sound (due to water drainage), contact 
your local authorized dealer.

 

Push down the lever after fi nish checking.

 

In case the water keep on draining out from the Tank Unit, switch off 
the system, and then contact your local authorized dealer.

EXPANSION VESSEL 

0

 PRE PRESSURE CHECKING

For Space Heating / Cooling

 

Expansion Vessel 

0

 with 10 L air capacity and initial pressure of 

1 bar is installed in this Tank Unit.

 

Total amount of water in system should be below 200 L.
(Inner volume of Tank Unit’s piping is about 5 L)

 

If total amount of water is over 200 L, please add another expansion 
vessel. (fi eld supply)

 

Please keep the installation height difference of system water 
circuit within 10 m.

CHECK RCCB/ELCB

Ensure the RCCB/ELCB set to “ON” condition before check RCCB/ELCB.
Turn on the power supply to the Tank Unit.
This testing could only be done when power is supplied to the Tank Unit.

 

WARNING

Be careful not to touch parts other than RCCB/ELCB test button when 
the power is supplied to Tank Unit. Else, electrical shock may happen.

 

Push the “TEST” button on the RCCB/ELCB. The lever would turn 
down and indicate “0”, if it functions normal.

 

Contact authorized dealer if the RCCB/ELCB malfunction.

 

Turn off the power supply to the Tank Unit.

 

If RCCB/ELCB functions normal, set the lever to “ON” again after 
testing fi nish.

INSTALLATION OF REMOTE 

CONTROLLER AS ROOM 

THERMOSTAT

7

 

Remote Controller 

1

 mounted to the Tank Unit can be moved to 

the room and serve as Room Thermostat.

Installation Location

 

Install at the height of 1 to 1.5 m from the fl oor (Location where 
average room temperature can be detected).

 

Install vertically against the wall.

 

Avoid the following locations for installation.
1.  By the window, etc. exposed to direct sunlight or direct air.
2.  In the shadow or backside of objects deviated from the room 

airfl ow.

3.  Location where condensation occurs (The Remote Controller 

is not moisture proof or drip proof.)

4.  Location near heat source.
5. Uneven surface.

 

Keep distance of 1 m or more from the TV, radio and PC. (Cause 
of fuzzy image or noise)

Remote Controller Wiring

1

2

Terminal for Remote Controller wiring

Remote Controller

Tank Unit

Remote Controller wiring 
(fi eld supply)

 

No polarity

Summary of Contents for WH-UD03JE5





































Reviews: