background image

1

ENGLISH

SAFETY PRECAUTIONS

 

Read the following “SAFETY PRECAUTIONS” carefully before installation of Air-To-Water Hydro Tank (here after referred to as “Tank Unit”).

 

Electrical works and water installation works must be done by licensed electrician and licensed water system installer respectively. Be sure to use 
the correct rating and main circuit for the model to be installed.

 

The caution items stated here must be followed because these important contents are related to safety. The meaning of each indication used is as 
below. Incorrect installation due to ignorance or negligence of the instructions will cause harm or damage, and the seriousness is classifi ed by the 
following indications.

 

Please leave this installation manual with the unit after installation.

 WARNING

This indication shows the possibility of causing death or serious injury.

 CAUTION

This indication shows the possibility of causing injury or damage to properties only.

The items to be followed are classifi ed by the symbols:

Symbol with white background denotes item that is PROHIBITED.

   

Symbol with dark background denotes item that must be carried out.

 

Carry out test run to confi rm that no abnormality occurs after the installation. Then, explain to user the operation, care and maintenance as stated in instructions.
Please remind the customer to keep the operating instructions for future reference.

 

If there is any doubt about the installation procedure or operation, always contact the authorized dealer for advice and information.

 

WARNING

Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacturer. Any unfi t method or using incompatible material 
may cause product damage, burst and serious injury.
Do not use unspecifi ed cord, modifi ed cord, joint cord or extension cord for power supply cord. Do not share the single outlet with other electrical appliances. Poor contact, 
poor insulation or over current will cause electrical shock or fi re.

Do not tie up the power supply cord into a bundle by band. Abnormal temperature rise on power supply cord may happen.

Keep plastic bag (packaging material) away from small children, it may cling to nose and mouth and prevent breathing.

Do not use pipe wrench to install refrigerant piping. It might deform the piping and cause the unit to malfunction.

Do not purchase unauthorized electrical parts for installation, service, maintenance and etc.. They might cause electrical shock or fi re.

Do not pierce or burn as the appliance is pressurized. Do not expose the appliance to heat, fl ame, sparks, or other sources of ignition.
Else, it may explode and cause injury or death.

Installation Manual

AIR-TO-WATER HYDRO TANK

WH-ADC0309J3E5UK

 CAUTION

R32

REFRIGERANT

This AIR-TO-WATER HYDRO TANK contains and 

operates with refrigerant R32.

THIS PRODUCT MUST ONLY BE INSTALLED OR SERVICED 

BY QUALIFIED PERSONNEL.

Refer to National, State, Territory and local legislation, 

regulations, codes, installation & operation manuals, before 

the installation, maintenance and/or service of this product.

Explanation of symbols displayed on the indoor unit or outdoor unit.

WARNING

This symbol shows that this equipment uses 
a fl ammable refrigerant. If the refrigerant is 
leaked, together with an external ignition 
source, there is a possibility of ignition.

CAUTION

This symbol shows that the Installation 
Manual should be read carefully.

CAUTION

This symbol shows that a service personnel 
should be handling this equipment with 
reference to the Installation Manual.

CAUTION

This symbol shows that there is information 
included in the Operation Manual and/or 
Installation Manual.

Required tools for Installation Works

1  Philips screw driver
2  Level gauge
3  Electric drill, hole core drill 

(ø70 mm)

4  Hexagonal wrench (4 mm)
5  Spanner
6  Pipe cutter
7  Reamer
8  Knife
9  Gas leak detector
10 Measuring tape

11 Thermometer
12 Megameter
13 Multimeter
14 Torque wrench

18 N•m (1.8 kgf•m)
55 N•m (5.5 kgf•m)
58.8 N•m (5.8 kgf•m)
65 N•m (6.5 kgf•m)
117.6 N•m (12.0 kgf•m)

15 Vacuum pump
16 Gauge manifold

ACXF60-37631-AB

Summary of Contents for WH-UD03JE5





































Reviews: