Panasonic WH-UD03JE5 Installation Manual Download Page 14 | Manualshive

Page: 14 / 36

background image

14

ENGLISH

APPENDIX

This section introduces variation of various systems using Air-To-Water Heatpump and actual setting method.

1-1 Introduce application related to temperature setting.

Temperature setting variation for heating

1. Remote Controller

Floor heating

Indoor

Outdoor

Connect fl oor heating or radiator directly to the Tank Unit.
Remote controller is installed on Tank Unit.
This is the basic form of the most simple system.

2. Room Thermostat

Outdoor

Tank Unit receive Room Thermo signal (ON/OFF) from Remote controller
to control HP and circulation pump.
There is a build-in thermistor in the remote controller.

Floor heating

Indoor

Connect fl oor heating or radiator directly to the Tank Unit.
Remove remote controller from Tank Unit and install it in the room where fl oor heating is installed.
This is an application that uses remote controller as Room Thermostat.

3. External Room Thermostat

Outdoor

Room
Thermostat
(Field supply)

Floor heating

Indoor

Connect fl oor heating or radiator directly to Tank Unit.
Remote controller is installed on Tank Unit.
Install separate external Room Thermostat (fi eld supply) in the room where fl oor heating is installed.
This is an application that uses external Room Thermostat.

Setting of remote controller

Installer setting

System setup

Optional PCB connectivity - No

Zone & Sensor:

Water temperature

Setting of remote controller

Installer setting

System setup

Optional PCB connectivity - No

Zone & Sensor:

Room thermostat

Internal

Setting of remote controller

Installer setting

System setup

Optional PCB connectivity - No

Zone & Sensor:

Room thermostat
(External)

1

Variation of system

«
...
12
13
14
15
16
...
»

Summary of Contents for WH-UD03JE5





































Reviews:

No comments

Related manuals for WH-UD03JE5

Brand: Palm Pages: 20

Brand: Bard Pages: 50

Brand: Lasko Pages: 4

Brand: L.B. White Pages: 18

Brand: L.B. White Pages: 18

ES38 RHFE-1004FTA

Brand: Rinnai Pages: 12

Alwayzaire P3062

Brand: Bestway Pages: 2

Brand: AL-KO Pages: 144

Brand: Acquaer Pages: 12

Brand: Ribitech Pages: 24

Brand: Schwank Pages: 33

GUARDIAN Smart Sense AD250

Brand: L.B. White Pages: 24

Brand: MILL Pages: 10

Brand: Samoa Pages: 38

Brand: Galletti Pages: 32

Brand: P.Lindberg Pages: 54

Brand: Lumme Pages: 10

Brand: ProMinent Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands