manualshive.com logo in svg

Panasonic Viera TC-P54Z1, Technical Manual

Share
Download
Panasonic Viera TC-P54Z1 Technical Manual Download Page 87

Slide #87

Wireless Unit Replacement 

(TX/RX m  RF remote control)

The RF remote control is included when the TX module is ordered. Therefore when TX and RX are 
replaced, the RF remote control is also changed.

The TX and the RX are automatically paired when they are connected to the Tuner and the Display Unit 
respectively.

The new remote control has to be registered before it can be used.

To establish connection between the transmitter module and the receiver module:

Connect the TX and the RX to the Tuner unit and the Display unit respectively.

Press the power button on the Tuner unit. (The tuner turns on)

Press the power button on the Display unit. (The display turns on)

The red LED on the TX and the RX should turn ON. When connection between TX and RX is 
established the LEDs turn green and the picture appears.

TX 

(

Transmitter module)

RX 

(Receiver module)

WT

WH

RM

WR

Wireless unit

WHD 

Transmitter

WHD Host

RF module

WHD Receiver

RM

RF module

Wireless unit

RF remote 
control module

Summary of Contents for Viera TC-P54Z1






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands