manualshive.com logo in svg

Panasonic Viera TC-P54Z1, Technical Manual

Share
Download
Panasonic Viera TC-P54Z1 Technical Manual Download Page 39

Slide #39

Power Supply Voltages Distribution 

STB5V

The STB5V is the first voltage generated by the (P-Multi) power supply. 
This voltage is used to activate the System and the Panel microprocessors in the DA board. 
STB5V is also used by the GH board (HDMI IN Board) and the KA board (IR Remote Receiver).

F+15V

The F+15V is the second voltage generated by the (P-Multi) power supply.
This voltage is the source of a DC to DC converter in the DA board which outputs SUB voltages. 
The SUB voltages are used to energize the signal processing section of the DA board.
F+15V is also used by the fan control circuit board (PB) and the HDMI board (GH).

Vsus

The Vsus is output when the power is turned on.
This voltage is generated by the (P-Vsus) section of the power supply and is used by the SC and 
SS boards for scan and sustain drive operation.

Vda

This voltages is generated by the (P-Multi) power supply and is used by the panel drive ICs built 
into the flex-cable between the panel and the data drive circuit boards (C boards).

P15V

This voltages is generated by the (P-Multi) power supply and is used by the SC and SS boards for 
scan and sustain drive operation. This voltage is also used by the audio amp. circuit in the DA 
board.
3.3V derived from the P15V is used by the panel drive ICs. 

P5V

The P5V is generated by the (P-Multi) power supply and is used by mostly all the boards involved in 
panel drive operation with the exception of the C1 board.

Summary of Contents for Viera TC-P54Z1






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands