manualshive.com logo in svg

Panasonic Viera TC-P54Z1, Technical Manual

Share
Download
Panasonic Viera TC-P54Z1 Technical Manual Download Page 59

Slide #59

Panel MPU SOS Detect (Continue)

4 Blinks SOS: 

When an over voltage condition of the voltage lines from the power supply occurs, 

pin 18 of connector A6 goes high. This high is provided to pin 67 of IC29003 of the DA board 
triggering the “POWER SOS” circuit. When this happens, the TV shuts down and the power LED 
blinks 4 times. Primarily the P board causes 4 blinks, followed by the DA board.

5 Blinks SOS: 

Pin 60 of the CPU IC29003 monitors the 5V line. During normal operation, pin 60 is 

kept high. If the 5V line is missing or shorted, a low is provided to pin 60. As a result, the unit shuts 
down and the power LED blinks 5 times.

6 Blinks SOS: 

Pin 65 of the CPU IC29003 monitors the status of the SC board. During normal 

operation, a low is applied to pin 65. If the SC board becomes defective, a high is provided to pin 
65. As a result, the unit shuts down and the power LED blinks 6 times.

7 Blinks SOS: 

Pin 68 of the CPU IC29003 monitors the status of the SC, SU, SD board. During 

normal operation, a low is applied to pin 68. If the SC, SU, or SD board becomes defective, a high 
is provided to pin 68. As a result, the unit shuts down and the power LED blinks 7 times.

8 Blinks SOS: 

Pin 66 of the MPU IC29003 monitors the status of the SS board. During normal 

operation, pin 8 of connector SS33 outputs a low to pin 66. If the SS board becomes defective, a 
high is provided to pin 66. As a result, the unit shuts down and the power LED blinks 8 times.
8 Blinks condition is also caused when the connections between the panel’s flex-cables and the 
sustain board is broken.

Summary of Contents for Viera TC-P54Z1






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands