Panasonic TX-51P800X Service Manual Download

Page: 39 / 50

10.3.3.6. "B-LINEAR" adjustment

Push the "TV/AV" buttons, and select the "B-LINEAR".Push the "Volume up/down" buttons, and adjust the "B-LINEAR". (Refer to
Fig. C.)

10.3.3.7. "B-PIN (V)" adjustment

Push the "TV/AV" buttons, and select the "B-PIN".Push the "Channel up/down" buttons, and adjust the "B-PIN (V)" (Refer to Fig.
D.)

10.3.3.8. "B-PIN (H)" adjustment

Push the "TV/AV" buttons, and select the "B-PIN".Push the "Volume up/down" buttons, and adjust the "B-PIN (H)". (Refer to Fig.
E.)

10.3.3.9. "B-CORNER" adjustment

Push the "TV/AV" buttons, and select the "B-CORNER".Push the "Channel up/down" buttons, and adjust the "B-CORNER". (Refer
to Fig. F.)

10.3.3.10. "B-KEY" adjustment

Push the "TV/AV" buttons, and select the "B-KEY".Push the "Channel up/down" buttons, and adjust the "B-KEY". (Refer to Fig. G.)

10.3.3.11. "B-STATIC" adjustment

Push the "TV/AV" buttons, and select the "B-STATIC.Push the "Channel/Volume up/down" buttons, and adjust "B-STATIC" so that
Horizontal & Vertical Center line is aligned with the bump in the screen center mark. (Refer to Fig. H.)

TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ

Summary of Contents for TX-51P800X



















































Search results

Summary of Contents for TX-51P800X

Reviews:

Related manuals for TX-51P800X

Brands by name

Popular brands

Panasonic TX-51P800X, Service Manual

Search results

Summary of Contents for TX-51P800X

Reviews:

Related manuals for TX-51P800X

Brands by name

Popular brands