![background image](http://html.mh-extra.com/html/panasonic/toughbook-cf-19kdraxcm/toughbook-cf-19kdraxcm_service-manual_270619037.webp)
9-14
n
Line Processing of Antenna Cable
9.2.4.
Setting up the LCD Hinge
1. Wind the Cable coming out of the LCD Unit counterclock-
wise to the LCD Hinge.
2. Set the Lock Plate and the Hinge Top Cover, and rotate
the LCD Hinge to turn the Display Unit to front
3. Put the LCD Cable and the Antenna Cable in the Cable
Holder.
4. Fit another Cable Holder and clamp the Cable Holders in
the LCD Hinge.
5. Fix the LCD Hinge using the 2 Screws <N17> and the 2
Cable Holder Plates.
Screws <N17 > : DXYN3+J8FNL
Ⅎ
ℵ
ℴ
ℳ
ℷ
ℶ
A
B
㪫㫆㫉㫈㫌㪼㩷㫆㪽㩷㫋㫀㪾㪿㫋㪼㫅㫀㫅㪾㩷㫊㪺㫉㪼㫎㪑㪑㪇㪅㪉㫧㪇㪅㪇㪉㪥䊶㫄㩿㻍㪉㪅㪇㫧㪇㪅㪉㫂㪾㪽䊶㪺㫄㪀
<Note>
Avoid any stress on the solder.
<Order of fixing screws>
㽲㸢㽳㸢㽴㸢㽵㸢㽶㸢㽷
Wrap around the ANT Cable
and insert between the ribs.
The cushion must come
within ± 2mm from the
center of the rib.
Insert into the Front
rib after wrapping.
Avoid overlapping of the Cable at right and left of the hook as below.
Insert into the Front
rib after wrapping.
Insert between
the rib.
Put the Cable on
each hook.
Put the Cable on
each hook.
䎦䏄䏅䏏䏈䎃䎦䏘䏖䏋䏌䏒䏑䎃䎶䎃
䎦䏄䏅䏏䏈䎃䎦䏘䏖䏋䏌䏒䏑䎃䎶䎃
䎤䎱䎷䎃䎸䏓䏓䏈䏕䎃䎯䏈䏉䏗
䎋䎺䎺䎤䎱䎃䎰䎤䎬䎱䎌
䎶䏆䏕䏈䏚
䎶䏆䏕䏈䏚
䎶䏆䏕䏈䏚
䎶䏆䏕䏈䏚
䎶䏆䏕䏈䏚
䎶䏆䏕䏈䏚
䎤䎱䎷䎃䎯䏒䏚䏈䏕䎃䎵䏌䏊䏋䏗
䎋䎺䎯䎤䎱䎃䎤䎸䎻䎒䎥䎷䎌
䎦䏄䏅䏏䏈䎃䎦䏘䏖䏋䏌䏒䏑
䎦䏄䏅䏏䏈䎃䎦䏘䏖䏋䏌䏒䏑
䎤䎱䎷䎃䎯䏒䏚䏈䏕䎃䎯䏈䏉䏗
䎋䎺䎯䎤䎱䎃䎰䎤䎬䎱䎒䎖䏕䏇䎌
Avoid running
over the rib,
boss and bin to
avoid catching
the Cable when
LCD Rear is set.
Avoid running
over the rib,
boss and bin to
avoid catching
the Cable when
LCD Rear is set.
Detail of "A"
䎤䎱䎷䎃䎸䏓䏓䏈䏕䎃䎵䏌䏊䏋䏗
䎋䎺䎺䎤䎱䎃䎤䎸䎻䎌
Detail of "B"
S2
S2
CAUTION
S1:Insulation S2:Bitten S3:Sharp Edge
S4:Part No. Check S5:Other
S2
S2
<N17>
<N17>
LCD Cable
Holder
Sheet
Cable
Holder
Cable
Holder
Cable
Holder
Plate
Cable Holder
Plate
Cable
Holder
Plate
LCD
Hinge