Panasonic TH-42LF60W Operating Instructions Manual Download Page 55 | Manualshive

Page: 55 / 68

Panasonic TH-42LF60W Operating Instructions Manual Download Page 55

55

Using Network Function

@J@:==@$Q

(connecting with a twisted pair cable transmitter)

This device is equipped with functions that allow Ethernet signals from a twisted pair cable transmitter to be received
through a LAN cable along with video/audio signals.

Hub or broadband router

"

COMPUTER

Twisted pair cable transmitter

LAN cable (not supplied)

LAN cable (not supplied)

Note:

+ &'$& K%*

Precautions for use while connecting with a twisted pair cable transmitter

Installing / Connecting

+ 'Q Z& &'> K

> & &'Z ZZ
fuzzy images and sounds.

+ The transmission distance between the twisted pair cable transmitter and the device is up to 100 meters.

:& K

+ Do not use a hub between the twisted pair cable transmitter and the Display.
+ When connecting to the Display using the twisted pair cable transmitter (receiver) of other maker, do not use

another twisted pair cable transmitter between the twisted pair cable transmitter of other maker and this device.
The images and sounds may be interrupted or become unstable.

+ >:Z ^

noise.

+ Lay out cables of the twist pair cable transmitter and this product away from other cables, especially from the

power supply cable.

+ When laying multiple cables, keep them as close together as possible running parallelly and not bundled.
+ >Z %*:' QZ =\?|&K

Twisted pair cables

+ Use a LAN cable between the twisted pair cable transmitter and the device that conforms to the following

conditions.
+ ¨

+ It is a straight cable

+ It is a shielded cable (with a connector)

+ It is a solid cable

+ When laying the cable(s), use an instrument such as a cable tester or cable analyzer and check whether the

cable characteristics are CAT5e or above. When using a relay connector along the path, also include this in the
measurements.

+ Do not pull cables hard. Also avoid forcefully bending or folding them.

Other

+ @& >|%=|\]]*K& >

':>>& [#K% K Z> K*

«
...
53
54
55
56
57
...
»

Summary of Contents for TH-42LF60W





































































Reviews:

No comments