manualshive.com logo in svg

Panasonic TH-42LF60W, Operating Instructions Manual, Page: 42 / 68

Share
Download
Panasonic TH-42LF60W Operating Instructions Manual Download Page 42

42

Setup for Input Signals

Component / RGB-in select

Select to match the signals from the source connected to the COMPONENT/RGB IN terminal.

Y, P

B

, P

R

 signals 

 “Component”

RGB signals 

 “RGB”

1/2

Signal

Input label

ECO Mode settings

Setup

Screensaver

Wobbling

Off

OSD Language

English(UK)

Component/RGB-in select

RGB

No activity power off

Disable

Press to display the Setup menu.

1

2

3

Press to select the “Component / RGB-in select”.

Press to select the desired mode.
Component 

 RGB

{>`K

Note:

+ Make setting of the selected input terminal (COMPONENT/RGB IN).

YUV / RGB-in select

Select to match the signals from the source connected to DVI-D IN terminal.

YUV signals 

 “YUV”

RGB signals 

 “RGB”

1/2

Signal

Input label

ECO Mode settings

Wobbling

Setup

Off

YUV/RGB-in select

RGB

Screensaver

No activity power off

Disable

OSD Language

English(UK)

Press to display the Setup menu.

1

2

3

Press to select the “YUV / RGB-in select”.

Press to select the desired mode.
YUV 

 RGB

{>`K

Summary of Contents for TH-42LF60W





































































Reviews:

No comments