Override function
WARNING
%
be manually operated from outside the dangerous area, and also
where the operators can see the entire dangerous area.
This function forcibly turns the safety function into invalid. This func-
the muting function needs to start the product with safety output 2 be
OFF status, when the product is required to continue operating even
though the muting sensor becomes valid after the muting sensor is
turned ON at the starting of line.
The override function becomes valid when all the conditions listed
#
$ The incandescent lamp with 3.6 to 30W shall be connected to
either muting lamp output 1 or 2, or to both of the inputs.
$ The signal shall be input to either muting sensor 1 or 2, or to both
of the inputs.
$ The override input terminal O1 and O2 shall be short-circuited
and the test input terminal T1 / T2 shall be opened within 1 sec.
(3 sec. continuously). The override function turns ON either short-
circuiting the override input terminal, or opening the test input
%
If one of the three conditions above becomes invalid or timing ex-
ceeds 60 sec., the override function becomes invalid.
Auxiliary output 1
Muting operation state is outputted.
% !^
% !
.\$H
Override operation state is outputted.
% % !^
% % !
Auxiliary output 3
Blown lamp is outputted.
(When the two lamps are connected, the signal is outputted if one of
them blows.)
!^
!
(Always OFF when only one lamp is used.)
Auxiliary output 4
The auxiliary output of the light curtain.
#'!^
%!
Interference prevention function
Max. three sets (total 192 beam channels) of the light curtain can be
connected in parallel by using the interference prevention terminals
(IE+, IE-, IR+ and IR-).
[ !!!]D! [
IE+
IE-
IR- IR+
SF-C14EX-01
IE+
IE-
IR- IR+
SF-C14EX-01
[ !!!]D!!+$*J!!"
>J!!!!*@+J$*J!
IE+
IE-
IR- IR+
SF-C14EX-01
Emitter of a unit of
light curtain
12-core cable for
light curtain
Interference prevention - (Gray / Black)
Interference prev (Gray)
>J!!!!*+J$*J!
IE+
IE-
IR- IR+
SF-C14EX-01
Receiver of a unit of
light curtain
Interference prev (Gray)
Interference prevention - (Gray / Black)
12-core cable for
light curtain
^ \6 + % #
SF-C14EX-01
s
should be 0.5m or less. If the length is 0.5m or more, use ø0.2mm
2
or more
shielded twisted pair cable.
2) The interference prevention wire for connection with a unit of light curtain
should be 12-core cable.
3) Refer to the instruction manual enclosed with the light curtain for details of
the connection with a unit of light curtain.
#5?/:#)2/.../^_#-
95/2).)9.:#5#5%..5
When using this product as a safety equipment for a press machine
in Japan, this product's installation, electrical wiring, inspection and
##=
'% '
supervisor who has completed special training as set forth by In-
dustrial Safety and Health Laws, and has extensive knowledge and
experience to resolve problems and any problems related to his /
her duties.
The muting function can be used only when the slide is rising. For
details, refer to “Standards for press machine or shears safety
equipment structure.”
When used in combination with
, this product satis-
7"& <
Safety and Health Laws Provision 44-2 as indicated below.
`>J!!*!@]!!DJ b
$ 7& ^
No. TA529 (
.
)
No. TA530 (
,
:
)
$ 0
Standards for press machine or shear safety equipment structure
(Ministry of Labor Notice No. 102, issued September 21, 1978)
When using
and this product as safety equipment
for a press machine in Japan, a pre-work inspection and periodic
inspection must be carried out by the press machine work supervi-
sor or by the person in charge of the matters listed in Provision 134,
No. 1, 2 and 4 of the Ordinance on Labor Safety and Hygiene. The
press machine work supervisor, etc., must inspect the following
matters before starting work, and must record and save the results.
@+
=
(safety distance and vertical position)
?
?# &
?
)+
=
(safety distance and vertical position)
?
?# &
? %
Application expansion unit SF-C14EX-01
"&
<
?#
Refer to “Policy on Press Machine Safety Equipment Control” (Min-
istry of Labor, Basic Publication No. 446-2, issued on July 9, 1993)
for details.
@]$@J!
$ When using this product as a safety equipment for a press machine
in Japan, the machine in which
and this product are
mounted must be capable of suddenly stopping from any operation
%
and this product with a machine having an irregular sudden stop.
$ % *
clutch.
$ When using this product as a safety equipment for a press machine
in Japan, do not use the product with a press machine that does not
Item
Model
Press machine having sudden stop device and restart
prevention mechanism
Pressure capacity
50,000kN or less
Sudden stop time
500ms or less
Stroke length
;? % * 6
Range of model height
Within bolster width
