4
./#255/#25.6)#/#25
2. Receiver side connector
1. Emitter side connector
> ;{6
4. Power indicator (Ui) (Green)
5. Test input indicator (TEST)
(Yellow)
6. Muting sensor 1 indicator
(MU1) (Orange)
7. Muting sensor 2 indicator
(MU2) (Orange)
8. Safety output 1 indicator (OUT1) (Green)
9. Safety output 2 indicator (OUT2) (Green)
10. Safety output 3 indicator (OUT3) (Green)
11. Output polarity
selection switch
15. Interlock 1 indicator
(INTERLOCK1)
(Yellow)
16. Interlock 2 indicator
(INTERLOCK2)
(Yellow)
17. Interlock 3 indicator
(INTERLOCK3)
(Yellow)
12. Auxiliary output 1 indi-
cator (AUX1) (Orange)
13. Auxiliary output 2 indi-
cator (AUX2) (Orange)
14. Auxiliary output 3 indi-
cator (AUX3) (Orange)
No.
Function
1
Emitter side connector
Connects the emitter of the light curtain.
2
Receiver side connector
Connects the receiver of the light curtain.
3
;{6
Lights up or blinks when an error occurs.
4
Power indicator (Ui) (Green)
Lights up when power is supplied.
5
Test input indicator (TEST) (Yellow)
Lights up when the test input is valid.
6
Muting sensor 1 indicator (MU1) (Orange) Lights up when muting sensor 1 is ON.
7
Muting sensor 2 indicator (MU2) (Orange) Lights up when muting sensor 2 is ON.
8
Safety output 1 indicator (OUT1) (Green) Lights up when safety output 1 is ON.
9
Safety output 2 indicator (OUT2) (Green) Lights up when safety output 2 is ON.
10 Safety output 3 indicator (OUT3) (Green) Lights up when safety output 3 is ON.
11 Output polarity selection switch
PNP (Minus earthing) or NPN (Plus
earthing) can be selected.
The factory setting is PNP (Minus
earthing).
12 Auxiliary output 1 indicator (AUX1) (Orange) Lights up when auxiliary output 1 is ON.
13 Auxiliary output 2 indicator (AUX2) (Orange) Lights up when auxiliary output 2 is ON.
14 Auxiliary output 3 indicator (AUX3) (Orange) Lights up when auxiliary output 3 is ON.
15 Interlock 1 indicator (INTERLOCK1) (Yellow) Lights up when interlock 1 is ON.
16 Interlock 2 indicator (INTERLOCK2) (Yellow) Lights up when interlock 2 is ON.
17 Interlock 3 indicator (INTERLOCK3) (Yellow) Lights up when interlock 3 is ON.
5
TERMINAL ARRANGMENT
Terminal
No.
Function
Terminal
No.
Function
14
Safety output 1 Light received /
blocked output of the light curtain
S11
Emergency stop contact input
2 NC input
Between S11 to S12
Between S21 to S22
24
S12
34
Safety output 2 Light curtain out-
put including the muting function
S21
44
S22
54
Safety output 3
Emergency stop output
X11
Safety output 1 reset input
\\\R7
\\\>*
64
X12
S3+
Muting sensor input 1
(PNP output type)
>>*?
>
X13
S3
X21
Safety output 2 reset input
R\RR7
R\R>*
S3-
X22
S4+
Muting sensor input 1
(NPN output type)
[[*?
[
X23
S4
X31
Safety output 3 reset input
>\>R7
S4-
X32
T1
Test input terminal
!+
* ^
AUX1 Auxiliary output 1 Muting output
T2
AUX2 Auxiliary output 2 Override output
O1
Override input terminal
!<% *
Valid
AUX3 Auxiliary output 3 Blown lamp output
O2
AUX4 Auxiliary output 4 Light curtain auxiliary output
L1+
Muting lamp output 1
IE+
Interference prevention terminal Em
L1-
IE-
Interference prevention terminal Emission -
L2+
Muting lamp output 2
IR+
Interference prevention terminal R
L2-
IR-
Interference prevention terminal Receipt -
A1
R[}0
A2
0V
6
#5/.66./#252#/#25(#)/#25(9/:2
>` <^
The installation position / direction is not basically limited.
?& <^
9#5
(optional)
>` <^
Always install this product in a control panel having an IP54 or high-
er protective structure.
7
MOUNTING TERMINAL BLOCK
When connecting to the terminal block, in-
sert a solid wire or twisted wire (lead wire)
with a ferrule (sleeve) terminal (please ar-
range separately) into the hole as shown
+ '
when it is properly inserted. However, do
not to pull the wire with excessive force,
as this can cause a cable break.
When connecting the twisted wire (lead
wire) without a ferrule (sleeve), insert the
wire to the innermost of the connecting
hole while pressing the release button.
When releasing the solid wire or the
twisted wire (lead wire), pull the wire while
pressing the release button.
Lead wire
Flathead screwdriver
Ferrule (sleeve)
terminal
(Please arrange separately)
Release button
Lead wire inlet
The following cables are recommended for power supply side con-
nector and other connector.
? ;\R6XRR`
2
(AWG 24 to 12)
!XR\`
2
(AWG 24 to 16)
8
:2)/#)#/)2//#25
The power supply unit of this product adopts an electronic fuse
which does not require any replacement.
When the electronic fuse is operated, turn OFF the power supply,
and remove the cause of overcurrent before restarting the power
supply for resetting.
The electronic fuse is not suitable to use in which the product is
operated continuously or daily. Note that operating the product con-
##
9
WIRING
When this product is connected to the light curtain, be sure to use
the following connecting cable.
SFB-CB05-EX
(cable length 0.5m),
SFB-CB5-EX
(cable length 5m)
SFB-CB10-EX
(cable length 10m)
%
(for emitter, cable length 10m)
%
(for receiver, cable length 10m)
When using this product as a safety equipment for a press machine
in Japan, be sure to use the following cable.
SFPB-CB05-EX
(cable length 0.5m),
SFPB-CB5-EX
(cable length 5m)
SFPB-CB10-EX
(cable length 10m)
%
(for emitter, cable length 10m)
%
(for receiver, cable length 10m)
The following cables are recommended for power supply side con-
nector and other connector.
? ;\R6XRR`
2
(AWG 24 to 12)
!XR\`
2
(AWG 24 to 16)
Cable extension is possible up to 50m (for each emitter / receiver).
However, 30m or less (for each emitter / receiver) for two sets in
series connection, and 20m or less (for each emitter / receiver) for
three sets in series connection.
Note that the cable cannot be extended for parallel connection.
