10.2.5. Service Mode Table 5
FL Display
Key Operation
Front Key
Item
Description
Mode Name
Initial setting
of laser drive
current
Press [FL Display] on
remote control unit for next
page (FL Display) on values
of laser drive current.
Cancelled automatically
5 seconds later.
(Display 1)
(Display 2)
In STOP (no disc) mode,
press [STOP] button on the
main unit, and [PAUSE]
button on the remote
control unit.
Initial setting of laser drive current.
Initial current value for the DVD laser
and CD laser is separately saved in
the EEPROM IC.
FL Display sequence:
Display 1 2.
DVD laser
drive current
measurement
Press [FL Display] on
remote control unit for next
page (FL Display) on values
of dvd drive current.
Cancelled automatically
5 seconds later.
(Display 1)
(Display 2)
In STOP (no disc) mode,
press [STOP] button on the
main unit, and [FL
DISPLAY] button on the
remote control unit.
DVD laser drive current measurement.
DVD laser drive current is measured
and the result is displayed together
with the initial value stored in the
EEPROM IC.
After the measurement, DVD laser
emission is kept on. It is turned off
when POWER key is switched off.
FL Display sequence:
Display 1 2.
DVD laser current
measurement mode
DVD
Laser
Initial Value
The value denotes the current in decimal
notation.
The above example shows the initial
current is XXXmA and the measured
value is YYYmA.
(Display 1)
(Display 2)
DVD
Laser
Value
Laser current
measurement
mode
CD
Laser
DVD Laser
Initialization
Cancelled automatically
5 seconds later.
Initialization.
User settings are cancelled and player
is initialized to factory setting.
It is necessary when after replacement
of Micro-processor (DV5 LSI) IC,
FLASH ROM IC (IC8651), EEPROM
IC (IC8611) & DVD Module P.C.B.
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [ 10] button on the
remote control unit.
Device check
To check the device.
In STOP (no disc)
mode, press [STOP]
button on the main unit,
and [4] button on the
remote control unit.
DVD Module
P.C.B. Reset
To reset DVD Module P.C.B.
This process is used when the DVD
Module P.C.B. or FLASH ROM
IC is replaced with a new one.
Cancelled automatically
5 seconds later.
Cancelled automatically
5 seconds later.
While in initialization
mode, press & hold
[STOP] button on the main
unit, follow by [ENTER]
button on the remote
control unit.
The value denotes the current in decimal
notation.
The above example shows the initial
current is XXXmA and YYYmA for CD
laser and DVD laser respectively when
the laser is switched on.
54
SA-PTX7P
Summary of Contents for SA-PTX7
