background image

T

Q

BJ09

97

4

Making the connections

Connect the AC mains lead only after all the other 

connections have been made.

1

Connect the antenna.

Place the antenna where reception is best.

• If radio reception is poor, use an outdoor antenna (not supplied).

2

Connect the speakers (sold separately).

Be careful not to cross (short-circuit) or reverse 

the polarity of the speaker wires as doing so may 

damage the speakers.

3

Connect the AC mains lead.

Do not use an AC mains lead with other equipment.

Conserving power

The system consumes a small amount of power (

14), 

even when it is in standby mode. Disconnect the power 

supply if you do not use the system.

Some settings will be lost after you disconnect the 

system. You have to set them again.

Note:

• Keep your speakers more than 10 mm from this unit for 

ventilation.

• Put the speakers on a flat safe surface.

• When you play at high levels for a long period, it can cause 

damage to the system and decrease the life of the system.

• Decrease the volume in these conditions to prevent 

damage:

- When you play distorted sound.

- When you adjust the sound quality.

You can connect a VCR, DVD player etc. 

Note:

• Disconnect the AC mains lead before connection.

• Switch off all equipment and read the appropriate operating 

instructions.

• Components and cables are sold separately.

• If you want to connect equipment other than those 

described, refer to the audio dealer.

• Sound distortion can occur when you use an adaptor.

Compatible speaker system (sold separately)

Use this unit with a 2 channel speaker system.

(Impedance: 3 

™ 

- 16 

)

• Using other speakers can damage the unit, and sound 

quality will be negatively affected.

Refer to the operating instructions for the speaker 

system for details.

2

2

1

To household mains socket

Tape 

(not supplied)

Be sure to fully tighten 

the nut.

CAUTION!

• Use the speakers only with the recommended 

system. If not, you can cause damage to the 

amplifier and speakers and can cause a fire.

Consult an approved service personnel if damage 

occurs or if there is a sudden apparent change in 

performance.

• Do the procedures included in these instructions 

when you attach the speakers.

This unit (rear)

To right speaker

To left speaker

Connecting other equipment

e.g. DVD player 

(not supplied)

This unit (rear)

Audio cable (not supplied)

SA-PMX82-M~TQBJ0997.book  4 ページ  2017年4月14日 金曜日 午前9時58分

Summary of Contents for SA-PMX82M

















Reviews: