Panasonic S-50PU2E5B, Technical Data & Service Manual, Page: 298 / 316

8 8
Point the transmitter of the remote controller at the receiver. When the signal is received correctly it will beep once.
(It beeps twice only when the unit starts operating.)
The signal can be received at a distance of about 6 meters. This distance should be used only as a guide.
It depends on battery strength.
Make sure nothing is between the remote controller and the receiver that could block the signal.
Do not leave the remote controller in direct sunlight, where the wind from the air conditioner can blow directly on it, or near
any other heat source.
Take care not to drop, throw or wash the remote controller with water.
The signal from the remote controller may not be received in rooms with rapid start fluorescent lighting, inverter lights, plasma
displays, LCD televisions (monitor), etc. For more information, please contact the dealer where the product was purchased.
1
2
Fasten the remote controller
holder with screws. Fitting the remote controller
in the holder.
Remote controller holder
Press
Put in
Checking Addresses
When you press on the remote controller, its current address appears on the display. If this address corresponds to the
address of a receiver , the buzzer sounds. (If it is on ALL, the buzzer will always sound.)
If it is on ALL, it can be operated regardless of receiver addresses. Point the remote controller at the receiver you wish to
operate and transmit.
8-26. Using the Remote Controller
Wall Mount Use
• Press from the location you wish to mount the remote controller
and make sure the signal is received properly.
• Pull the remote controller forward to remove it.
Don’t get the remote controller too far away from the receiver.
This may cause a malfunction. Be sure to keep the remote controller in the same room as the receiver.
8-27. For Best Results
Point the remote controller at the receiver.
When the signal is received properly, it will beep one time.
Avoid locating the remote controller where it is covered, such as behind a curtain.
Keep it out in the open.
In both multi and single unit installations,
when more than one indoor units are installed in the same room with a
compatible wireless remote controller, addresses can be set up to avoid crosstalk. By setting the address switches on the
receivers and matching them with the number of addresses on the remote controller, up to six indoor units can be controlled
separately with the remote controller. (When using units in a flexible combination or operating multiple units simultaneously,
they cannot be controlled individually as they are operated at the same time.) There are separate address settings, receiver
addresses for the receivers and transmitter addresses for the remote controller.
For more information, please contact the distributor where the product was purchased.
8-28. Addresses
• These settings are saved in nonvolatile memory in the remote controller, so even when its batteries are changed, the settings
do not have to be made again.
Control of 2WAY SYSTEM
2. Wireless Remote Controller
Matching up Addresses
Setting Remote Controller Addresses
1. If you press
and at the same time , “ ” will blink.
2. While holding down, every time you press , it cycles from ALL 1 2 3…
Set it to the receiver address switch of the indoor unit you wish to operate.
3. When you release , the address that was displayed is set.
When you do this, if it corresponds to the receiver’s address setting, the buzzer sounds.
6 ALL.
Address
Display on the
Remote
Controller
CZ-RWSU3
Position of
receiver’s
(inside indoor
unit) address
switch The position of the
receiver’s address
switch does not
matter.
For 1, 2 and 3, set the switch on the
right and for 4, 5 and 6, to the left.
CZ-RWSC3
Position of
the Receiver’s
Address Switch
The position of the
receiver’s address
switch does not
matter.
For 1, 2 and 3, set the switch on the
left and for 4, 5 and 6, to the right.
• Please do not hold the [Emergency Operation] button of the indoor unit down while the indoor unit’s display lamps are
blinking one after another.
• Make sure to operate while the indoor unit is stopped.
• The address of indoor unit is set to "ALL" at the time of the shipment.
NOTE
8-22
SM830276-00_欧州向け R32シングル TD＆SM.indb 22 19/02/18 11:16:08