Panasonic S-3650PF3E Technical Data & Service Manual Download Page 90

Page: 90 / 321

1-11-1-1-14

Others

Setting No.

(1)

Remote controller

setting data

Item code 5d

0001

Contents &

optional parts name

Air-flow blocking kit

(for 3-way air flow)*

High-ceiling setting 1*

(3)

0003

Air-flow blocking kit

(when a duct is

connected.)

(6)

High-ceiling setting 2*

0006

(1) Checking After Installation

1) Check that there are no gaps between the unit and the

panel for cassette, or between the panel for cassette
and the ceiling surface.
* Gaps may cause water leakage and condensation.

2) Check that the wiring is securely connected.

* If it is not securely connected, the auto flap will not

operate.
(“P09” is displayed on the remote controller.)
In addition, the water leakage and condensation may
occur.

(2) Operating the Wireless Remote Controller

For details of installation, refer to the section “Wireless
Signal Receiver” in the supplied installation instructions.

(3) Selecting DC Fan Motor Tap (4-Way Cassette)

Check the optional parts accordingly in the following
table.

Table for DC Fan Motor Tap Settings*

Air-flow blocking kit

(for 2-way air flow)*

*1 When using optional parts in different setting No. in

*2 Ceiling height (m)

combination with multiple units, conform it to the larger
setting No.

Indoor unit type

S-3650PU3E S-6071PU3E

Standard

2.7

3.0

(factory setting)

High-ceiling setting 1

3.2

3.3

High-ceiling setting 2

3.5

3.6

3.8

Air-flow blocking kit

(for 3-way air flow)

4.2

Air-flow blocking kit

(for 2-way air flow)

1) When setting on the indoor unit control PCB

Stop the system before performing these steps.

1 Open the electrical component box cover, then

check the indoor unit control PCB.

2 Change the DIP switch (SW001) on the indoor unit

control PCB in accordance with the setting number

which was confirmed in “Table for DC Fan Motor

Tap Settings”.

Setting No.

DIP switch

Setting No.

DIP switch

(1)

TP6

TP3

TP1

1 2 3

(6)

TP6

1 2 3

TP3

TP1

(3)

TP6

1 2 3

TP3

TP1

<Procedure of CZ-RTC5B>
Stop the system before performing these steps.

1 Keep pressing the

and

buttons

simultaneously for 4 or more seconds.
The “Maintenance func” screen appears on the LCD
display.

2 Press the

button to see each menu.

press the

button.

If you wish to see the next screen instantly, press the

button.

Select “8. Detailed settings” on the LCD display and

The “Detailed settings” screen appears on the LCD display.

TP6

TP3

TP1

2 3

TP6

TP3

TP1

1 2 3

SW001

Indoor unit control PCB

Setting example

1: OFF

2: OFF

3: ON

Maintenance func

Sel.

20:30 (THU)

Page [

] Confirm

1. Outdoor unit error data

2. Service contact

3. RC setting mode

4. Test run

Maintenance func

Sel.

20:30 (THU)

Page [

] Confirm

5. Sensor info.

6. Servicing check

7. Simple settings

8. Detailed settings

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 14

20/01/30 10:25:11

Summary of Contents for S-3650PF3E


































































































































































































































































































































Search results

Summary of Contents for S-3650PF3E

Reviews:

Related manuals for S-3650PF3E

Brands by name

Popular brands

Panasonic S-3650PF3E, Technical Data & Service Manual

Search results

Summary of Contents for S-3650PF3E

Reviews:

Related manuals for S-3650PF3E

Brands by name

Popular brands