Panasonic S-3650PF3E Technical Data & Service Manual Download Page 218

Page: 218 / 321

4-13

4 4

4-12-7. Compressor Overheating Prevention Control

Instructed frequency for compressor operation will be regulated by compressor temperature. The changes of

frequency are as below.

If compressor temperature exceeds 103°C, compressor will be stopped.

Compressor = OFF

Compressor Frequency

Reduce

Compressor Frequency

Limited

Free

103°C

99°C

96°C

Comp. temperature

88°C

87°C

86°C

4-12-8. Deice Operation

When outdoor pipe temperature and outdoor air tempertature is low, deice operation start where indoor fan motor

and outdoor fan motor stop.

4-12-6. Cooling Freeze Prevention Control

The following control is performed during cooling operations (including dry mode operation), in accordance

with whichever of the indoor heat exchanger temperatures (E1 or E2) is lower. (See the chart below.)

(a) Frequency will not be decreased less than 5.5 minutes after thermostat ON.

(b) The threshold value is increased in accordance with the indoor load (differences of temperature).

min(E1, E2)

11°C

≥

9°C

10°C

≥

7°C

9°C

≥

5°C

6°C

≥

0°C

Free

Frequency reduce

Frequency limited

Compressor stop in 360 seconds

Frequency maintain

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 13

2020/01/30 13:58:47

Summary of Contents for S-3650PF3E


































































































































































































































































































































Search results

Summary of Contents for S-3650PF3E

Reviews:

Related manuals for S-3650PF3E

Brands by name

Popular brands

Panasonic S-3650PF3E, Technical Data & Service Manual

Search results

Summary of Contents for S-3650PF3E

Reviews:

Related manuals for S-3650PF3E

Brands by name

Popular brands