Panasonic S-3650PF3E Technical Data & Service Manual Download Page 181

Page: 181 / 321

2-2-1

Type U3

2-2. Precautions

Request that the customer be present when the test run is performed.

At this time, explain the operation manual and have the customer perform the actual steps.

Check that the 220 – 240 VAC power is not connected to the inter-unit control wiring connector terminal.

*If 220 – 240 VAC is accidentally applied, the indoor unit control PCB fuse will blow in order to protect the PCB.

INDOOR UNIT CONTROL PCB

EMG

(CN044,

OC (CN040, blue)

brown)

Jumper

(JP040)

Type F3

EMG

(CN044,

OC (CN040, blue)

brown)

Jumper

(JP040)

In this case, make the wiring correctly.

Then disconnect the 2P connectors (OC) that are

connected to the indoor unit control PCB, and replace

them with 2P connectors (EMG).

If operation is still not possible after changing the brown

connectors, cut the jumper on the indoor unit control

PCB. (Be sure to turn the power OFF before performing this work.)

Be sure to set the external static pressure before performing the

Be sure to set the external static pressure before performing the test run.

test run.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 1

2020/01/29 19:52:15

Summary of Contents for S-3650PF3E


































































































































































































































































































































Search results

Summary of Contents for S-3650PF3E

Reviews:

Related manuals for S-3650PF3E

Brands by name

Popular brands

Panasonic S-3650PF3E, Technical Data & Service Manual

Search results

Summary of Contents for S-3650PF3E

Reviews:

Related manuals for S-3650PF3E

Brands by name

Popular brands