Chapter 3
Basic Operations — Switching on/off the projector
ENGLISH - 57
Initial setting (operation setting)
Set the items for the operating method depending on the projector’s application and duration of usage.
After completed the initial setting, you can change the settings of each item from the [PROJECTOR SETUP]
menu. If you change the settings while using the projector, the duration until the luminance of light source
decreases by half may shorten or the luminance may decrease.
By using this initial setting (operation setting), you can complete the settings at once when installing the projector,
if the operation method of the projector is determined in advance. If [ALL USER DATA] is executed from the
[PROJECTOR SETUP] menu
→
[INITIALIZE], do not change the initial setting (operation setting) and proceed to
next initial setting (installation setting) by pressing the <ENTER> button. If you need to change the setting, ask the
person responsible for this projector (such as a person in charge of equipment or operation).
2/7
100%
100%
INITIAL SETTING
SET
CHANGE
MENU SELECT
OPERATING MODE
CONSTANT MODE
NORMAL
OFF
LINK
GROUP A
ENTER
CALIBRATION TIME
OFF
CALIBRATION MESSAGE
ON
BRIGHTNESS CONTROL SETUP
LIGHT OUTPUT
MAX LIGHT OUTPUT LEVEL
Set the way to use the projector. For details, please
refer to the operating instructions "When the initial
setting screen is displayed".
Note
f
The preceding initial setting screen is displayed when the projector is switched on for the first time after purchase. If [ALL USER DATA] is
executed from the [PROJECTOR SETUP]
→
[INITIALIZE], the settings before execution are displayed in [OPERATING MODE] and [MAX
LIGHT OUTPUT LEVEL].
f
For the relationship between the luminance and the runtime, refer to “Interrelation of luminance and runtime” (
x
page 59).
f
For details on each setting item, refer to the [PROJECTOR SETUP] menu
→
[OPERATION SETTING].
1) Press
as
to select [OPERATING MODE].
2) Press
qw
to switch the item.
f
The items will switch each time you press the button.
f
Set [OPERATING MODE] to anything other than [ECO], [LONG LIFE1], [LONG LIFE2], or [LONG LIFE3]
when using the projector at an altitude of 2 700 m (8 858') or higher above sea level.
[NORMAL]
*1
Set this item when high luminance is required. The estimated runtime is approximately 20 000 hours.
[ECO]
*1
Set this item to increase the life of the light source though it will lower the luminance than [NORMAL].
The estimated runtime is approximately 24 000 hours.
[LONG LIFE1]
*1
Set this item to increase the life of the light source though it will lower the luminance than [ECO]. The
estimated runtime is approximately 43 000 hours.
[LONG LIFE2]
*1
Set this item to increase the life of the light source though it will lower the luminance than [LONG
LIFE1]. The estimated runtime is approximately 61 000 hours.
[LONG LIFE3]
*1
Set this item to increase the life of the light source though it will lower the luminance than [LONG
LIFE2]. The estimated runtime is approximately 87 000 hours.
[USER1]
Set [MAX LIGHT OUTPUT LEVEL] and [LIGHT OUTPUT] individually.
[USER2]
[USER3]
*1
The runtime is estimated when the [PICTURE] menu
→
[DYNAMIC CONTRAST] is set to [3].
f
When [NORMAL], [ECO], [LONG LIFE1], [LONG LIFE2], or [LONG LIFE3] is selected, proceed to Step
5)
.
3) Press
as
to select [MAX LIGHT OUTPUT LEVEL].
4) Press
qw
to adjust.
Operation
Adjustment
Range of adjustment
Press
w
.
Increases the maximum level of brightness correction.
8.0 % - 100.0 %
Press
q
.
Decreases the maximum level of brightness correction.
5) Press
as
to select [LIGHT OUTPUT].
