Chapter 3
Basic Operations — Switching on/off the projector
42 - ENGLISH
2) Press the <ENTER> button to proceed to the initial setting.
Initial setting (operation setting)
Set the items regarding the operating method depending on the duration of use and the usage of the projector.
After completed the initial setting, you can change the settings of each item from the [PROJECTOR SETUP]
menu. If you change the settings while using the projector, the estimated runtime may shorten or the luminance
may decrease.
This initial setting (operation setting) is prepared to complete the settings at once during the installation when
the operation of the projector is predetermined. When the [PROJECTOR SETUP] menu
→
[INITIALIZE]
→
[ALL USER DATA] is executed, do not change the setting in the initial setting (operation setting) and press the
<ENTER> button and proceed to next initial setting (installation setting). Request to the person responsible for this
projector (such as a person in charge of equipment or operation) when it is necessary to change the setting.
2/7
100.0%
INITIAL SETTING
SET
CHANGE
MENU SELECT
OPERATING MODE
CONSTANT MODE
NORMAL
OFF
LINK
ENTER
CALIBRATION TIME
OFF
CALIBRATION MESSAGE
ON
BRIGHTNESS CONTROL SETUP
LIGHT OUTPUT
Set the way to use the projector.
For details, please refer to the
operating instructions "When the
initial setting screen is displayed".
Note
f
The preceding initial setting screen is displayed when the projector is switched on for the first time after purchase. If the [PROJECTOR
SETUP] menu
→
[INITIALIZE]
→
[ALL USER DATA] is executed, the settings before execution are displayed in [OPERATING MODE].
f
For the relationship between the luminance and the runtime, refer to “Interrelation of brightness and runtime” (
x
page 43).
f
For details on each setting item, refer to the [PROJECTOR SETUP] menu
→
[OPERATION SETTING].
1) Press
as
to select [OPERATING MODE].
2) Press
qw
to switch the item.
f
The items will switch each time you press the button.
f
Set [OPERATING MODE] to [NORMAL], [USER1], [USER2], or [USER3] when using the projector at an
altitude of 2 700 m (8 858') or higher above sea level.
[NORMAL]
Set this item when high luminance is required. The estimated runtime is approximately 20 000 hours
*1
.
[ECO]
The luminance will decrease compared to [NORMAL], but set this item to increase the expected life of
the light source. The estimated runtime is approximately 24 000 hours
*1
.
[QUIET]
The luminance will decrease compared to [NORMAL], but set this item to prioritize the operation with
less noise. The estimated runtime is approximately 20 000 hours
*1
.
[LONG LIFE1]
The luminance will decrease compared to [ECO], but set this item to increase the expected life of the
light source. The estimated runtime is approximately 43 000 hours
*2
.
[LONG LIFE2]
The luminance will decrease compared to [LONG LIFE1], but set this item to increase the expected life of
the light source. The estimated runtime is approximately 61 000 hours
*2
.
[LONG LIFE3]
The luminance will decrease compared to [LONG LIFE2], but set this item to increase the expected life of
the light source. The estimated runtime is approximately 87 000 hours
*2
.
[USER1]
Set [LIGHT OUTPUT] as desired.
[USER2]
[USER3]
*1 Estimated runtime is the time until the brightness decreases to approximately half of the time of delivery when the projector is used
with the [PICTURE] menu → [DYNAMIC CONTRAST] set to [2] and under environment of 0.15 mg/m
3
dust.
The value of runtime is just an estimate, and is not the warranty period.
*2 Estimated runtime is the time the initial brightness of the long life mode is basically maintained constant when the projector is used
with the [PICTURE] menu → [DYNAMIC CONTRAST] set to [2].
The value of runtime is just an estimate, and is not the warranty period.
3) Press
as
to select [LIGHT OUTPUT].
4) Press
qw
to adjust.
