Panasonic PN28160A Operation Manual Download Page 48

Page: 48 / 277

(6) MDIX Mode

Shows the Auto MDI/MDI-X setting.
Auto

The Auto MDI/MDI-X is enabled.

Crossover

The Auto MDI/MDI-X is disabled.

(7) Line Protocol

Shows the loop detection function setting.
Up

The loop detection is enabled.

Disabled

The loop detection is disabled.

(8) Line Shut-down

Shows the time between the loop-detection/port-shutdown and the auto-recovery.

(9) Power-saving

Shows the MNO series power saving mode.
Half

The MNO series power saving mode is enabled (Half).

Full

The MNO series power saving mode is enabled (Full).

Disabled

The MNO series power saving mode is disabled.

(10) Max Frame Size

Shows the maximum frame size (including a VLAN tag) that can be transmitted.

(11) Accept Frames

Shows the frame types to accept.
VLAN tagged
and untagged

Receives both frames with VLAN tags and without VLAN tags.

VLAN tagged only

Receives only VLAN-tagged frames.

(12) Link Status

Shows the port status.
Up

The port link is up.

Down

The port link is down.

Disabled

The port is shut down.
(The port is closed, or it is disconnected by the loop detection function.)

Summary of Contents for PN28160A






















































































































































































































































































Search results

Summary of Contents for PN28160A

Reviews:

Brands by name

Popular brands

Panasonic PN28160A, Operation Manual

Search results

Summary of Contents for PN28160A

Reviews:

Brands by name

Popular brands