manualshive.com logo in svg

Panasonic PN28160A, Operation Manual, Page: 190 / 277

Share
Download
Panasonic PN28160A Operation Manual Download Page 190

 

 

190

<Command Entry Example> 

An example of executing the command to show the bandwidth control configuration is 
shown below. 

 

 

 

Fig. 4-6-1 Example of executing the command to show the bandwidth control configuration 

(1) Port 

Shows the port number. 

 
(2) Bandwidth 

Shows the bandwidth. The factory default setting is 1000. (The unit is Mbps.) 

 
(3) Status 

Shows the bandwidth control status (Enabled or Disabled). 
enabled 

The bandwidth control is enabled. 

disabled 

The bandwidth control is disabled. 

 

M24eG> enable 
M24eG# show egress-rate-limit 
  Port         Bandwidth       Status 
  ---------    ------------    --------- 
  1            1000            disabled 
  2            1000            disabled 
  3            1000            disabled 
  4            1000            disabled 
  5            1000            disabled 
  6            1000            disabled 
  7            1000            disabled 
  8            1000            disabled 
  9            1000            disabled 
  10           1000            disabled 
  11           1000            disabled 
  12           1000            disabled 
  13           1000            disabled 
  14           1000            disabled 
  15           1000            disabled 
  16           1000            disabled 
  17           1000            disabled 
  18           1000            disabled 
  19           1000            disabled 
  20           1000            disabled 
  21           1000            disabled 
  22           1000            disabled 
  23           1000            disabled 
  24           1000            disabled 
M24eG# 

(1) 

(3)

(2)

Summary of Contents for PN28160A






















































































































































































































































































Reviews:

No comments