manualshive.com logo in svg

Panasonic PN28160A, Operation Manual, Page: 251 / 277

Share
Download
Panasonic PN28160A Operation Manual Download Page 251

 

 

251

(4) Shows the log classification. 

ARL 

A log relating to MAC address table 

CLI 

A log relating to CLI 

CONSOLE 

A log relating to console 

LINE-PROTOCOL 

A log relating to loop detection function 

PORT 

A log relating to port 

SNMP 

A log relating to SNMP 

SNTP 

A log relating to SNTP 

SYSTEM 

A log relating to system 

TELNET 

A log relating to telnet 

VLAN 

A log relating to VLAN 

DOT1X 

A log relating to IEEE802.1X (This function is not supported.) 

 
(5) Details of logs are as follows. 

ARL 

Memory allocation fail! 

err 

Indicates that allocation of memory for MAC address table has failed. 

CLI 

Get reboot timer fail. 

warn 

Indicates that the operation of reboot timer has failed. 

Reboot: Factory Default Except IP. 

Indicates that the Switching Hub was rebooted in the mode to return settings 
other than IP addresses to the factory default. 

Reboot: Factory Default. 

Indicates that the Switching Hub was rebooted in the mode to return all settings 
to the factory default. 

Reboot: Normal. 

info 

Indicates that the Switching Hub was rebooted. 

CONSOLE 

Login from console 

info 

Indicates that the login operation was executed via console, and was successful.

LINE-PROTOCOL 

PortX auto recovery. 

Indicates that Port X has auto-recovered from shutoff after loop detection. 

The loop detected between portA and portB. 

Indicates that a loop was detected between Port A and Port B. 

The loop detected on portX. 

info 

Indicates that a loop was detected on Port X. 

PORT 

err 

PortX hardware register set fail in port initialization! 

Summary of Contents for PN28160A






















































































































































































































































































Reviews:

No comments