EN8
To Grind Meat
How to Use
1
Release the fixing lever and place the head onto the opening of
the motor housing.
•
Align the head vertically before push fully into the opening.
•
If the head is not set properly, the head is needed to turn right
and left slightly to get the correct alignment before push in.
Holding the head with one hand and tighten the head by closing
up the fixing lever.
2
Place the feed screw into the head, long end first, by turning the
feed screw slightly until it is set into the slot of the head.
•
If the feed screw is not set properly, it does not turn.
3
Place the cutting blade onto the feed screw shaft with the
blade facing the front as illustrated.
•
Cutting surface should be faced to the cutting plate
when being set, otherwise meat will not be ground.
4
Place the desired cutting plate over the cutting blade by fitting
its slot onto the feed screw shaft.
•
If the cutting plate is not set properly, meat may be leak out
around shaft in opening of motor housing. When meat leak out,
clean around the shaft in opening of motor housing.
Wipe with a well-wrung cloth.
Unplug when assembling the unit. Before plugging in, ensure the switch is off.
(Attaching)
shaft in opening of the motor housing
MK-ZJ3500_eng.indd EN8
2017/04/26 12:03:04
Job Name
100185265_MK-ZJ3500_2700中東向取説
Color
K
File Name
0008_MK-ZJ3500_eng.pdf
Refine Time
2018-05-31 11:21:28
Print Time
2019-11-22 13:04:09
Job Name
100185265_MK-ZJ3500_2700中東向取説
Color
K
File Name
0008_MK-ZJ3500_eng.pdf
Refine Time
2018-05-31 11:21:28
Print Time
2019-11-22 13:04:09
EN9
When meat jammed inside of the head
1
Switch off and wait until the motor has stopped completely.
2
Hold on to the motor housing then push in and turn the switch to “Reverse” for a few seconds.
(Do not turn it more than 5 seconds.)
When the switch is turned on, LED will light up. (Only MK-ZJ3500)
Then turn the switch back to “Off”.
3
Unplug and detach the parts by reversing steps on “To Grind Meat” from 3-5 to remove
ingredients in the head.
4
Attach the parts again and continue grinding meat.
5
Screw the cap into the head firmly.
Place the hopper plate on the head and fix it into position.
Set the unit on a firm surface.
•
The air vents at the bottom and the side of the motor
housing should be kept free and not blocked.
6
Cut all foods into pieces so that they fit easily into the
hopper opening.
Plug in, then switch on.
When the switch is turned on, LED will light up.
(Only MK-ZJ3500)
Place foods on the hopper plate and feed foods into the
hopper opening.
•
Use the food pusher.
Please hold the hopper plate with one hand when using the
food pusher.
•
When grinding nuts, feed handful portion into hopper opening
slowly one at a time. (Do not feed them continuously. Otherwise
the circuit breaker protection may activate.)
Use speed 2 (High speed) for grinding nuts. (Only MK-ZJ3500)
After use, switch off and unplug.
Note:
•
The head may wobble slightly during use, but it is normal. Do not over tighten the
fixing lever to stop this movement. It may cause damage.
But if the fixing lever is get looser, tighten the fixing lever again.
•
You may feel that the circuit breaker is activated easily when you are grinding large
or hard ingredients, but it is normal.
When meat does not come out from the cutting plate due to the jam of bones or other hard ingredient,
follow the below steps to release it.
(Grinding Meat)
MK-ZJ3500_eng.indd EN9
2017/04/26 11:35:32
Job Name
100185265_MK-ZJ3500_2700中東向取説
Color
K
File Name
0009_MK-ZJ3500_eng.pdf
Refine Time
2018-05-31 11:21:26
Print Time
2019-11-22 13:04:09
