Panasonic LQ-DRM200, Operating Instructions Manual

Page: 24 / 70

24
Timer recording
Manual programming
[RAM] [DVD-R]
Remote control only
You can set your own programming conditions (up to 16
programmes).
Preparation
≥
Switch [DVD, TV]
(19)
to “DVD”.
≥
Ensure that this unit’s clock is set correctly.
≥
Insert a disc for recording (make sure there is enough room for
the programme you are going to record plus a little extra).
1
Press [PROG/CHECK]
(13)
.
≥
The Timer Programme List screen appears.
A line that is ready for programming is highlighted.
2
Press [ENTER]
(10)
.
≥
The Timer Programme Correction screen appears.
3
Use [
1
]
(10)
to move through the items and change
the items with [
3
,
4
]
(10)
.
≥
The current settings are shown each time you press [
1
]
(10)
.
≥
You may use the numeric buttons
(4)
to enter “Name”,
“Date”, “Start” and “Stop”.
≥
Name (Programme Position/TV Station Name)
≥
Date
Current date
!)
the day before one month later
!)
Daily (Sunday to Saturday)
!)
Daily (Monday to
Saturday)
!)
Daily (Monday to Friday)
!)
Weekly
(Sundays)
!)
…
!)
Weekly (Saturdays)
!)
Current date…
≥
Start (start time)/Stop (finish time)
The time increases or decreases in 30-minute increments if
you hold the button.
≥
Mode (Recording mode)
XP
!)
FR
!)
EP
!)
LP
!)
SP
!)
XP… (page 19)
≥
Title
Select “Title” and press [ENTER]
(10)
, then refer to page 27
for entering title.
4
Press [ENTER]
(10)
when you have finished making
changes.
≥
To continue programming:
Repeat steps 2, 3 and 4.
5
Press [PROG/CHECK]
(13)
or [RETURN]
(28)
.
To put the unit on recording standby
Press [ , TIMER]
(14)
.
Ensure “ ” lights on the unit’s display.
To change the timer recording programme
1) While the Timer Programme List Screen is being shown, use
[
3
,
4
]
(10)
to select the programme you want to change, and
press [ENTER]
(10)
to show the Timer Programme Correction
screen.
≥
You may also select programme by inputting a 2-digit number
using the numeric buttons
(4)
.
≥
Use [
2
,
1
]
(10)
to move to the page preceding or following
the one on display.
2) Move through the items with [
1
]
(10)
and change the settings
with [
3
,
4
]
(10)
and press [ENTER]
(10)
.
Note
≥
The built-in clock employs 24-hour system.
≥
The remaining time is not shown if you insert discs other than
DVD-RAM or DVD-R.
≥
The remaining time displayed is calculated based on the current
recording mode.
≥
If the disc is protected (pages 28, 61), the unit switches to
standby but does not go on standby for recording. Check the disc
carefully.
≥
“PROG FULL” is displayed in the unit’s display if there are already
16 items programmed. Delete unnecessary items (page 25).
≥
Recording is not possible unless you set “Disc Protection” in
“DISC INFORMATION” to “Off” (page 28).
≥
You cannot record to a disc if the write protect tab on a cartridge
disc is set to protect. Release this before operation (page 61).
≥
Even if the unit is put in the timer recording standby mode or the
timer recording is being performed, you can play a programme.
≥
When recording more than one programme in a row, for
DVD-RAM the first few seconds, and for DVD-R about the first
30 seconds of all programmes from the second one onwards will
not be recorded.
RETURN
SELECT
SP OK 1:22 1:19 AV1 15/ 7 TUE 01
Mode
Disc
space
Stop Start No. Name Date
1:58 SP
TIMER
RECORDING
Remain
1:19:00 15.7 TUE
ENTER
New Timer Programme
Press ENTER to store
new programme.
RETURN
SELECT
1:58 SP
TIMER
RECORDING
Remain
1:55:00 15.7 TUE
ENTER
--:-- --/-- ---
Mode Stop Start Name Date
--:-- SP
Please set Input.
Title
1:58 SP
TIMER
RECORDING
Remain
1:19:00 15.7 TUE
2:00 15/ 7 TUE
Mode Stop Start Name Date
SP AV1 1:00
Title
E60TEG.book 24 ページ ２００３年９月１日 月曜日 午後５時６分