![background image](http://html.mh-extra.com/html/panasonic/lc4h-ps-r4-ac240v/lc4h-ps-r4-ac240v_manual_260848004.webp)
85
Setting the operation mode and counter
Setting procedure 1) Setting the operation mode (input mode and output mode)
Set the input and output modes with the DIP switches on the side of the counter.
DIP switches
Setting procedure 2) Setting the set value
Set the set value with the UP and DOWN keys on the front of the counter.
Front display section
DIP switch
Item
DIP switch No.
1
2
3
ON
ON
ON
SHOT-A
OFF
OFF
OFF
SHOT-B
ON
OFF
OFF
SHOT-C
OFF
ON
OFF
SHOT-D
ON
ON
OFF
HOLD-A
OFF
OFF
ON
HOLD-B
ON
OFF
ON
HOLD-C
OFF
ON
ON
—
Output mode
Output mode
Refer to table 1
1
2
3
Minimum reset input signal width
20 ms
1 ms
4
Maximum counter setting
30 Hz
5 kHz
5
Input mode
Refer to table 2
6
7
8
ON
OFF
DIP switch No.
6
7
8
ON
ON
ON
Addition input
OFF
OFF
OFF
Subtraction input
ON
OFF
OFF
Directive input
OFF
ON
OFF
Independent input
ON
ON
OFF
Phase input
OFF
OFF
ON
—
ON
OFF
ON
—
OFF
ON
ON
—
(See note 1)
(See note 1)
(See note 1)
(See note 1)
Input mode
Notes:1) The counter and set value displays will display DIP Err.
Notes:
2) Set the DIP switches before installing the counter on the panel.
Notes:
3) When the DIP SW setting is changed, turn off the power once.
Notes:
4) The DIP switches are set as ON before shipping.
ON
1
5
2
3
4
6
7
8
DIP switches (See note 2)
(Same for 6-digit, screw-down terminal type)
• 4-digit display type
Q
Counter display
W
Set value display
E
Controlled output indicator
R
Reset indicator
T
Lock indicator
Y
UP keys
Changes the corresponding
digit of the set value in the
addition direction (upwards)
U
DOWN keys
Changes the corresponding digit of the set
value in the subtraction direction (down-
wards)
I
RESET switch
Resets the counting value and the output
O
SET/LOCK switch
This is used to handle pre-scaling values,
one-shot times, decimal point position set-
tings, and key lock operations (to disable Up
key, Down key, and Reset key operations).
9
8
5
4
7
6
2
1
3
DOWN
UP
SET/LOCK
RESET
LOCK
RST
OP.
LC4H
COUNTER
RESET
LOCK
RST
OP.
LC4H
COUNTER
8
7
5
4
6
2
1
3
SET/LOCK
• 6-digit display type
Q
Counter display
W
Set value display
E
Controlled output indicator
R
Reset indicator
T
Lock indicator
Y
UP keys
Changes the corresponding digit of the set
value in the addition direction (upwards)
U
RESET switch
Resets the counting value and the output
I
SET/LOCK switch
This is used to handle pre-scaling values,
one-shot times, decimal point position set-
tings, and key lock operations (to disable Up
key, Down key, and Reset key operations).
Table 1: Setting the output mode
Table 2: Setting the input mode
LC4H-S
Setting procedure 3) Setting the input mode
The input mode is set using the key switch in the [Display] section on the front of the counter.
• Decimal point position setting mode
Q
Holding down the [SET/LOCK] key, press the key for the second digit to access the decimal point position setting mode.
W
When the setting mode has been accessed, release the [SET/LOCK] key.
Example) 6-digit type
Decimal point position setting mode display
(Example shows default value displayed)
02/2003