Panasonic KXTVS200 - VOICE MAIL SYSTEM Installation Manual Download

Page: 95 / 318

4.3

COMMON DIGITAL INTEGRATION FEATURES AND SETUP PROCEDURES

INTEGRATING THE VPS WITH THE PANASONIC KX-TD DIGITAL PBX

4.3.13 Voice Mail Transfer Button

This feature is used to transfer calls directly to a Voice Mailbox. It can be used with DPT or
Inband Signaling.

Enter Station Programming.

Press

unused

FLEXIBLE

(

DSS/BLF

) button.

Press [8].

Screen output: VTR.

Press

Voice Processor Extension.

Press STORE

Summary of Contents for KXTVS200 - VOICE MAIL SYSTEM































































































































































































































































































































Search results

Summary of Contents for KXTVS200 - VOICE MAIL SYSTEM

Reviews:

Related manuals for KXTVS200 - VOICE MAIL SYSTEM

Brands by name

Popular brands

Panasonic KXTVS200 - VOICE MAIL SYSTEM, Installation Manual

Search results

Summary of Contents for KXTVS200 - VOICE MAIL SYSTEM

Reviews:

Related manuals for KXTVS200 - VOICE MAIL SYSTEM

Brands by name

Popular brands