Panasonic KX-UDS Series Step By Step Installation Download Page 50

Page: 50 / 53

Appendix B : How to find out IP Address of Super Master CS

1. Turn on the CS (Super Master) while holding RESET Switch.

2. Release the RESET Switch when the LED flashes [Green/Red/Amber] alternately,
then the IP address is set to [192.168.0.241].
3. Log in to http://192.168.0.241/
4. Input ID and Password for administrator.

ID : admin

Password : adminpass

Method to find out IP address of Super Master CS

・

DHCP server

Access to DHCP server, and find out IP address of Super Master CS

・

Packet capture software

Download packet capture software

・

Register one PS

Execute following procedure (If PS is registered, please execute from step 12)

Log in by WEB Browser

ID: admin

Pass : adminpass

RESET Switch

Summary of Contents for KX-UDS Series






















































Search results

Summary of Contents for KX-UDS Series

Reviews:

Related manuals for KX-UDS Series

Brands by name

Popular brands

Panasonic KX-UDS Series, Step By Step Installation

Search results

Summary of Contents for KX-UDS Series

Reviews:

Related manuals for KX-UDS Series

Brands by name

Popular brands