Panasonic KX-UDS Series Step By Step Installation Download Page 16 | Manualshive

Page: 16 / 53

background image

16

© Panasonic Corporation 2017

16

This step is no need if you use DHCP server.

1. Turn on the CS

(Super Master

・

Slave

・

Air Sync Master)

while holding

RESET Switch.

LED: Green > Amber > OFF > Green/Red/Amber alternate flashing

2. Release the RESET Switch when

the LED flashes [Green/Red/Amber] alternately,

then the IP address is set to [192.168.0.241].

3. Log in to

http://192.168.0.241/

4. Input ID and password for administrator.

ID : admin
Password : adminpass

5. After log in, Configure network settings
   of CS and click [Save].

[Network] → [Basic Network Setting]

6. Log in to the Web user interface again
using the newly assigned IP address for the CS.

2.2 Basic Network Configuration <Step1> : Basic Network Setting

«
...
14
15
16
17
18
...
»

Summary of Contents for KX-UDS Series






















































Reviews:

No comments

Related manuals for KX-UDS Series

Brand: NEC Pages: 36

Brand: NEC Pages: 174

Brand: NEC Pages: 6

Brand: NEC Pages: 66

Brand: NEC Pages: 62

Brand: Panasonic Pages: 30

Brand: Panasonic Pages: 18

Brand: Samsung Pages: 2

Brand: Samsung Pages: 68

Brand: Samsung Pages: 89

Brand: Samsung Pages: 72

Brand: Samsung Pages: 59

Brand: Samsung Pages: 42

Brand: Samsung Pages: 15

Brand: Jabra Pages: 16

SP200 - QUICKSTART GUIDE 1

Brand: Jabra Pages: 372

JABRA FREEWAY HFS100

Brand: Jabra Pages: 40

Brand: Jabra Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands