59
KX-TG4753B/KX-TG470B/KX-TGA405B
12.2.5. Commands (Base Unit)
See the table below for frequently used commands.
12.2.6. Commands (Handset)
See the table below for frequently used commands.
Command name
Function
Example
rdeeprom
Read the data of EEPROM
Type “rdeeprom 00 00 FF”, and the data from address
“00 00” to “FF” is read out.
readid
Read ID (RFPI)
Type “readid”, and the registered ID is read out.
writeid
Write ID (RFPI)
Type “writeid 00 18 E0 0E 98”, and the ID “0018 E0 0E
98” is written.
hookoff
Off-hook mode on Base
Type “hookoff”.
hookon
On-hook mode on Base
Type “hookon”.
getchk
Read checksum
Type “getchk”.
How to use of
"getchk"
1.rdeeprom
Read EEPROM
Type “RdEeprom 03 F2 04”, and the data from address
“03 F2” to “03 F5” is read out
*This command gets 4 byte "WW", "XX", "YY", "ZZ".
*Please NEVER forget these 4 byte data!
2.sendchar epw
Write EEPROM
Type “sendchar epw 03 F2 04 FF FF FF FF”
3.sendchar RST
Reset baseset
Type “sendchar RST”
4.getchk
Read checksum
Type “getchk”.
5.sendchar epw
Write EEPROM
Type “sendchar epw 03 F2 04 WW XX YY ZZ”
*"WW", "XX", "YY", "ZZ" is 4 byte data that already read
from same address.
wreeprom
Write the data of EEPROM
Type “wreeprom 01 23 45”. “01 23” is address and “45”
is data to be written.
bs_burst
Base unit outputs RF power in burst
test mode on antenna 2
Type"bs_burst"
tx_high
Keep TX power high
Type"tx_high"
tx_low
Keep TX power low
Type"tx_low"
Command name
Function
Example
rdeeprom
Read the data of EEPROM
Type “rdeeprom 00 00 FF”, and the data from address
“00 00” to “FF” is read out.
readid
Read ID (RFPI)
Type “readid”, and the registered ID is read out.
writeid
Write ID (RFPI)
Type “writeid 00 18 E0 0E 98”, and the ID “0018 E0 0E
98” is written.
getchk
Read checksum
Type "getchk"
How to use of
"getchk"
1.rdeeprom
Read EEPROM
Type “RdEeprom 03 7D 04”, and the data from address
“03 7D” to “03 80” is read out
*NEVER forget the read 4 byte data!
2.sendchar epw
Write EEPROM
Type “sendchar epw 03 7D 04 FF FF FF FF”
3.sendchar RST
Reset baseset
Type “sendchar RST”
4.getchk
Read checksum
Type “getchk”.
5.sendchar epw
Write EEPROM
Type “sendchar epw 03 7D 04 WW XX YY ZZ”
*"WW", "XX", "YY", "ZZ" is 4 byte data that already read
from same address.
weeprom
Write the data of EEPROM
Type”wreeprom 01 23 45”. “01 23” is address and “45”
is data to be written.
hs_burst Handset outputs RF power in burst
test mode
Type"hs_burst"
tx_high
Keep TX power high
Type"tx_high"
tx_low
Keep TX power low
Type"tx_low"
