45
KX-TG4753B/KX-TG470B/KX-TGA405B
10.1.8.5. TEST RANGE Check
Circuit block which range is defective can be found by the following check.
CHART1: Setting of TX Power and RX Sensitivity in Range Confirmation TX TEST, RX TEST
Note:
(*1) Refer to
Commands (Base Unit)
(P.59).
10.1.8.6. TEST RANGE Check (Range Extender)
CHART1: Setting of TX Power and RX Sensitivity in Range Confirmation TX TEST, RX TEST
Note:
(*2) Refer to
Commands (Base Unit)
(P.59)
Item
BU (Base Unit) Check
HS (Handset) Check
Range Confirmation TX TEST
(TX Power check)
HS, BU setting
Checked unit: Low TX power (*1)
Regular unit: High TX power (*1)
1. Register Regular HS to BU (to be checked).
2. Set TX Power of the BU and the Regular HS
according to CHART1.
3. At distance of about 20m between HS and BU,
Link OK = TX Power of the BU is OK.
No Link = TX Power of the BU is NG.
1. Register HS (to be checked) to Regular BU.
2. Set TX Power of the HS and the Regular BU
according to CHART1.
3. At distance of about 20m between HS and BU,
Link OK = TX Power of the HS is OK.
No Link = TX Power of the HS is NG.
Range Confirmation RX TEST
(RX sensitivity check)
HS, BU setting
Checked unit: High TX power (*1)
Regular unit: Low TX power (*1)
1. Register Regular HS to BU (to be checked).
2. Set TX Power of the BU and the Regular HS
according to CHART1.
3. At distance of about 20m between HS and BU,
Link OK= RX Sensitivity of the BU is OK.
No Link = RX Sensitivity of the BU is NG.
1. Register HS (to be checked) to Regular BU.
2. Set TX Power of the Checking HS and the Reg-
ular BU according to CHART1.
3. At distance of about 20m between HS and BU,
Link OK= RX Sensitivity of the HS is OK.
No Link = RX Sensitivity of the HS is NG
BU (to be checked)
Regular_HS
TX Power
TX Power
BU (Base Unit) TX Power Check
Low
High
BU (Base Unit) RX Sensitivity Check
High
Low
HS (to be checked)
Regular_BU
TX Power
TX Power
HS (Handset) TX Power Check
Low
High
HS (Handset) RX Sensitivity Check
High
Low
Item
RE (Range Extender) Check
Range Confirmation TX TEST
(TX Power check)
HS, setting
Checked unit: Low TX power (*2)
Regular unit: High TX power (*2)
1. Register Regular HS and RE (to be checked) to Regular BU.
2. HS is power ON with “1“, “6“and “#“.
3. Set TX Power of the RE and the Regular HS according to CHART1.
4. At distance of about 20m between HS and RE,
Link OK = TX Power of the RE is OK.
No Link = TX Power of the RE is NG.
Range Confirmation RX TEST
(RX sensitivity check)
HS, BU setting
Checked unit: High TX power (*2)
Regular unit: Low TX power (*2)
1. Register Regular HS and RE (to be checked) to Regular BU.
2. HS is power ON with “1“, “6“and “#“.
3. Set TX Power of the RE and the Regular HS according to CHART1.
4. At distance of about 15cm between BU and RE,
5. At distance of about 20m between HS and RE,
Link OK= RX Sensitivity of the RE is OK.
No Link = RX Sensitivity of the RE is NG.
RE (to be checked)
TX Power
RE(Range Extender) TX Power Check
Low
RE(Range Extender) RX Sensitivity Check
High
