Panasonic KX-TCD965EC Operating Instructions Manual Download Page 79

Page: 79 / 84

Chapter 6

Useful Information

Problem

The unit does not work.

You cannot program items such as the
time/day adjustment (p. 20).

The battery strength is not displayed
correctly.

“

” flashes or the unit beeps every

15 seconds.

You charged the batteries fully, but
“

” flashes.

The charge indicator (

) light never

goes out while charging.

Remedy

•

Turn the power ON (p. 14).

•

Check the settings (p. 11–18).

•

Charge the batteries fully (p. 13).

•

Clean the charge contacts and charge again (p. 13).

•

Unplug the AC adaptor and turn the power OFF to
reset. Plug in the AC adaptor and turn the power ON.
Then try again.

•

The handset has been cancelled or has not been
registered. Register the handset (p. 64).

•

Re-install the handset batteries and try again.

•

Programming is not possible while the unit is in the
talk or intercom mode.

•

Move closer to the base unit.

•

Check that the battery type selection is correct
(p. 74).

•

Charge the batteries fully (p. 13).

•

Clean the charge contacts and charge again (p. 13).

•

Install new batteries (p. 74, 81).

•

This is normal.

General

KX-TCD965EC-6(74~84) 99.12.10 5:48 PM Page 79

Summary of Contents for KX-TCD965EC





















































































Search results

Summary of Contents for KX-TCD965EC

Reviews:

Related manuals for KX-TCD965EC

Brands by name

Popular brands

Panasonic KX-TCD965EC, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD965EC

Reviews:

Related manuals for KX-TCD965EC

Brands by name

Popular brands