Panasonic KX-TCD965EC Operating Instructions Manual Download Page 62

Page: 62 / 84

Remote Operation with the Handset

Direct commands

NEW MESSAGE PLAYBACK

•

Only new messages are played
back.

ALL MESSAGE PLAYBACK

•

All messages are played back.

REPEAT (During playback)

•

The current message is repeated.

SKIP (During playback)

•

The current message is skipped.
The next message is played.

STOP (During playback)

•

Playback is temporarily stopped.

•

To resume playback, press
again within 15 seconds, or the
voice menu (p. 61) will start.

ERASING A SPECIFIC MESSAGE
(During playback)

•

The current message is erased.

•

A short beep will sound and the
next message will be played.

ERASING ALL MESSAGES

•

All recorded messages are
erased.

•

A long beep sounds and “

message

” is heard.

ANSWERING SYSTEM OFF

•

The answering system is turned
off and will not answer calls until
turned on again.

ANSWERING SYSTEM ON

•

The answering system is turned
on and is in the stand-by mode
for receiving calls.

Recording your telephone conversation using the handset

You can record a telephone conversation.

During a conversation, press

then

•

“

Recording

” is displayed on the handset.

Continue your conversation.

When finished, press

then

•

When you record your 2-way telephone
conversation, you should inform the other
party that the conversation is being recorded.

•

A beep sounds every 15 seconds while
recording your conversation.

KX-TCD965EC-4(54~62) 99.9.27 8:01 PM Page 62

Summary of Contents for KX-TCD965EC





















































































Search results

Summary of Contents for KX-TCD965EC

Reviews:

Related manuals for KX-TCD965EC

Brands by name

Popular brands

Panasonic KX-TCD965EC, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD965EC

Reviews:

Related manuals for KX-TCD965EC

Brands by name

Popular brands