Panasonic KX-TCD505NL Operating Instructions Manual Download Page 22

Page: 22 / 90

Using the Telephone

Key Lock

You can lock the handset dialling buttons. Only incoming calls are accepted while the
key lock is ON. When the key lock is ON, the menu icon

changes to

When the key lock is ON, emergency calls cannot be made until key lock is
cancelled.

Key Lock ON

Key Lock OFF

Handset Locator/Paging

You can locate a misplaced handset by paging it.

Paging

To Stop Paging

•

You can also stop paging by pressing

•

When the ringer volume is off (p. 46), the handset will ring at the lowest level.

(Standby Mode
Display)

Press and hold

JOYSTICK

directly

for more than 2
seconds.

Press and hold

JOYSTICK

directly

for

more than 2 seconds once more.

<Base Unit>

Press

PAGE

<All Handsets>

All registered handsets ring for 1 minute.

<Base Unit>

Press

PAGE

<One of Handsets>

Press

TALK.

505NL_e.book Page 16 Thursday, July 10, 2003 4:56 PM

Summary of Contents for KX-TCD505NL



























































































Search results

Summary of Contents for KX-TCD505NL

Reviews:

Related manuals for KX-TCD505NL

Brands by name

Popular brands

Panasonic KX-TCD505NL, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD505NL

Reviews:

Related manuals for KX-TCD505NL

Brands by name

Popular brands