Panasonic KX-TCD505NL Operating Instructions Manual Download Page 16

Page: 16 / 90

Setting up

Connection

Plug in the AC adaptor and the telephone
line cord in order

•

The AC adaptor must remain
connected at all times. (It is normal for
the adaptor to feel warm during use.)

•

Never install telephone wiring during a
lightning storm.

•

USE ONLY WITH Panasonic
AC ADAPTOR PQLV19CE.

Battery Installation

Please ensure the batteries are inserted
as shown.

part should be inserted first.

Close the cover as indicated by the arrow.

•

When you replace the batteries, part
should be removed first.

Battery Charge

At the time of shipment, the batteries are
not charged. To charge, place the
handset on the base unit.

Please charge

the batteries for about 7 hours before
initial use.

During charging, the charge LED will light
as shown below.

During charging

Fully charged

The handset which power is off will be
turned on automatically when it is placed
on the base unit.

The handset will not operate while it is
on the base unit.

If you do not recharge the handset battery
for more than 15 minutes, the display will
flash

when the handset is lifted off

the base unit.

LINE

Fasten the AC
adaptor cord to
prevent it from
being
disconnected.

Hook

Hooks

Display icon

Battery strength

High

Medium

Low

Needs to be

charged

Red

Green

505NL_e.book Page 10 Thursday, July 10, 2003 4:56 PM

Summary of Contents for KX-TCD505NL



























































































Search results

Summary of Contents for KX-TCD505NL

Reviews:

Related manuals for KX-TCD505NL

Brands by name

Popular brands

Panasonic KX-TCD505NL, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD505NL

Reviews:

Related manuals for KX-TCD505NL

Brands by name

Popular brands