Panasonic KX-TCA130FXS Service Manual Download Page 25

Page: 25 / 115

8 OPERATIONS

8.1. Turning the Power On/Off

Power on

Press [

] for about 1 second.

The display will change to the standby mode.

Power off

Press [

] for about 2 seconds.

The display will go blank.

8.2. Setting the Date and Time

Important:

Confirm that the AC adaptor is connected.

Ensure that

is not flashing. If the handset is in screen saver mode,

is not displayed. Press [

] to turn the display

on.

Note:

To correct a digit, press

to move the cursor, then make the correction.

The date and time may be incorrect after a power failure. In this case, set the date and time again.

8.3. Redialling

Previously dialled phone numbers (each 24 digits max.) can be redialled.

8.3.1. Making a Call Using the Redial List

The last 10 phone numbers dialled are stored in the redial list.

8.3.2. Redialling the Last Number Dialled

KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT

Summary of Contents for KX-TCA130FXS




















































































































Search results

Summary of Contents for KX-TCA130FXS

Reviews:

Related manuals for KX-TCA130FXS

Brands by name

Popular brands

Panasonic KX-TCA130FXS, Service Manual

Search results

Summary of Contents for KX-TCA130FXS

Reviews:

Related manuals for KX-TCA130FXS

Brands by name

Popular brands