Panasonic KX-TCA130FXS Service Manual Download Page 8

Page: 8 / 115

4 BATTERY

4.1. Battery Installation

1. Insert the batteries negative ( ) terminal first.

2. Close the handset cover.

Note:

Use only rechargeable Ni-MH batteries P03P (HHR-4EPT).

4.2. Battery Charge

Place the handset on the base unit for about 7 hours before initial use.

When charging,

and battery strength icon are alternately shown on the display. When the batteries are fully charged,

flashes.

Note:

It takes 7 hours to fully charge the batteries, however, you can use the handset before the batteries are fully charged.

Clean the charge contacts of the handset and base unit with a soft, dry cloth, otherwise the batteries may not charge
properly. Clean if the unit is exposed to grease, dust or high humidity.

When

flashes, recharge the handset batteries.

will continue to flash until the batteries have been charged for at

least 15 minutes.

If the handset is turned off, it will be turned on automatically when it is placed on the base unit.

KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT

Summary of Contents for KX-TCA130FXS




















































































































Search results

Summary of Contents for KX-TCA130FXS

Reviews:

Related manuals for KX-TCA130FXS

Brands by name

Popular brands

Panasonic KX-TCA130FXS, Service Manual

Search results

Summary of Contents for KX-TCA130FXS

Reviews:

Related manuals for KX-TCA130FXS

Brands by name

Popular brands