Panasonic KX-HGW200 Operating Instructions Manual Download Page 18 | Manualshive

Page: 18 / 68

background image

18

“

Setup

To connect an Ethernet Hub to the KX-HGW200:

If you are not currently using an Ethernet hub to network more than one
computer, please skip this page.

1

Make sure the computers and other devices connected to the Ethernet
Hub are turned off.

2

Set the HUB/PC switch of the KX-HGW200 to HUB.

3

Connect the category 5 straight cable to
TO COMPUTER/ETHERNET HUB port of the KX-HGW200.

4

Connect the other end of the category 5 straight cable to the LAN port
of the Ethernet Hub.

HUB/PC switch

HUB

PC

To RJ-45 jack
on the cable/
xDSL modem

TO COMPUTER/
ETHERNET HUB port

Category 5
straight cable

Ethernet Hub

LAN port

Note:
Do not connect the category 5 straight cable to the UPLINK port of the
Ethernet Hub.

Note:
If using an Ethernet connection, an Ethernet card and software have
to be installed properly on the computer first.

PQQX12817ZA \1-P29

01.3.8

3:17

PM

y [ W 18

«
...
16
17
18
19
20
...
»

Summary of Contents for KX-HGW200





































































Reviews:

No comments

Related manuals for KX-HGW200

Brand: XiNCOM Pages: 82

Brand: Ubee Pages: 99

TTN Gateway v1 - EU

Brand: The Things Network Pages: 20

Brand: Comtrend Corporation Pages: 84

Brand: LifeShield Pages: 2

Smart Command 410100

Brand: Caroma Pages: 2

Brand: Luminext Pages: 8

Brand: SELECTRONIX Pages: 28

Brand: Planet Networking & Communication Pages: 19

Brand: Planet Networking & Communication Pages: 93

HomePortal 5011NV

Brand: 2Wire Pages: 18

Brand: ActionTec Pages: 4

Brand: ActionTec Pages: 89

Brand: AUDAC Pages: 16

Brand: Wireless Sensors Pages: 35

Brand: Renu Electronics Pages: 46

Brand: IBM Pages: 28

Brand: Nexcom Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands