Panasonic KW8M User Manual Download | Manualshive

Page: 77 / 87

background image

KW8M Eco-POWER METER

68

8.3 How to Remove

When disposing the unit or replacing battery, refer to the below procedure and remove the battery.
Undo wiring when disposing the unit or replacing battery. Electrical shock may occur if you touch places
where high voltage is present. Also, release any static electricity in your body before proceeding.

Hooks

Hooks

1. Remove 2 hooks at the top and bottom of the case and

draw PC board block from the case.

2. Remove 2 hooks from the block and remove the PC

board with battery.

3. Insert a tool between holder and battery and take battery

and put it on the stopper.

4. Push battery to the marked direction from back and

take it.

8.4 How to Mount
*Mount new battery within 3 minutes after removing the old battery.

1. Insert the battery in a battery holder horizontally, and
insert by the marked direction with + side facing up.

2. Make sure the battery is securely placed in the battery
holder.

Connector

Hooks

Hooks

3. Insert PC board block with battery to connector so that
it is fixed with 2 hooks of top and bottom.
The side with battery is inside.

4. Insert PC board block to the end not to make mistake
the direction and fix with 2 hooks correctly.

* If the direction is different, it can not be inserted
to the end. Be sure to check the direction.

«
...
75
76
77
78
79
...
»

Summary of Contents for KW8M
























































































Reviews:

No comments

Related manuals for KW8M

Brand: Omega Engineering Pages: 22

SourceMeter 2400

Brand: Keithley Pages: 594

System SourceMeter 2601B

Brand: Keithley Pages: 864

Brand: Labgear Pages: 8

SourceMeter 2600B Series

Brand: Keithley Pages: 897

Brand: NCTE Pages: 10

Brand: VeEX Pages: 842

Brand: lanry Pages: 2

Brand: lanry Pages: 29

Vigilantplant NFBU200-S Series

Brand: YOKOGAWA Pages: 24

Brand: horiba Pages: 117

Brand: Sequid Pages: 111

Brand: LEM Pages: 33

ENERGETIQ LDLS EQ-99X

Brand: Hamamatsu Pages: 45

Brand: Genie Pages: 14

DigiFlow 6710M-22

Brand: Savant Pages: 3

Brand: Lafayette Instrument Pages: 12

350 Maritime V2

Brand: TESTO Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands