Panasonic KW8M User Manual Download

Page: 52 / 87

KW8M Eco-POWER METER

◆

Ratio of estimated demand

・

It displays the ratio of estimated demand.

(Estimated demand:2.5kW, Demand setting value:5.0kW -> ratio of estimated demand is 50.0%.)

・

It displays [

－－－－

] when demand setting value is set to ”0.00kW”, when the ratio is over 999.9%,

and for 1 minute after starting the demand span.

・

[

－－－－

] is displayed until when the next demand span starts, when you change clock to before

demand span or to next demand span, or at power failure.

Remaining time to demand span is displayed at the bottom line with present demand, estimated
demand, and ratio of estimated demand. The remaining time is updated every 1 minute.

・

Display

Elapse time

00 to 59 seconds

1m 00s to 10m 59s

11m 00s to 29m 59s

Remaining

time

30 minutes

29 to 20minutes

19 to 1minutes

Display

3 (1digit)

2 (1digit)

1 to 19 (2 digits)

After 1 second

Remaining time to

demand span

[DEMAND]

Lighting

Remaining
time

Elapse

Summary of Contents for KW8M
























































































Search results

Summary of Contents for KW8M

Reviews:

Related manuals for KW8M

Brands by name

Popular brands

Panasonic KW8M, User Manual

Search results

Summary of Contents for KW8M

Reviews:

Related manuals for KW8M

Brands by name

Popular brands