Panasonic k-nl304g User Manual Download Page 195

Page: 195 / 198

187

Figure 5-97

Please refer to the following sheet for detailed information.

Type

Parameter

Function

Alarm

Type

Video loss

System alarms when video loss occurs.

Motion detection

System alarms when motion detection alarm

occurs.

Tampering

System alarms when camera is viciously masking.

HDD full

System alarms when disk is full.

HDD error

System alarms when disk error occurs.

External alarm

Alarm input device sends out alarm.

IPC

external

alarm

It refers to the on-off signal from the network

camera. It can activate the NVR local activation

operation.

IPC offline

System can generate an alarm when the network

camera and the NVR are disconnected.

Operation

Prompt

Check the box here, system can automatically pops

up an alarm icon on the Alarm button in the main

interface when there is an alarm.

Alarm

Sound

Play

alarm

sound

System sends out alarm sound when an alarm

occurs. You can specify as you wish.

Sound path

Here you can specify alarm sound file.

5.12

Log out

Click log out button, system goes back to log in interface. See Figure 5-98.

You need to input user name and password to login again.

Summary of Contents for k-nl304g







































































































































































































Search results

Summary of Contents for k-nl304g

Reviews:

Related manuals for k-nl304g

Brands by name

Popular brands

Panasonic k-nl304g, User Manual

Search results

Summary of Contents for k-nl304g

Reviews:

Related manuals for k-nl304g

Brands by name

Popular brands