Panasonic K-EF134L02AE Operation Manual Download Page 63

Page: 63 / 82

Figure 4-33

Please refer to the following sheet for detailed information. (K-EW214L01E and K-EF234L01E)

Parameter Function
Event

Type

It includes: No SD Card, SD Card Error and Capacity Warning

Enable

Check to alarm when SD card is abnormal.

Send

After you enabled this function, the system can send out email to alarm

the specified user.
This function is invalid when network is offline or IP conflict occurs.

SD Card

Capacity

Limit

User can set SD card capacity that is left free. When SD card space left

is smaller than this limit, alarm occurs.

When device is offline or IP conflicts, the abnormal alarm is similar with case of SD card error.

Parameter Function
Event

Type

It includes: Disconnection, IP Conflict

Enable

Check to alarm when network is abnormal.

Record

System auto activates to record once alarm occurs.

Record

Delay

System can delay the record for specified time after alarm ended. The

value ranges from 10s to 300s.

Summary of Contents for K-EF134L02AE



















































































Search results

Summary of Contents for K-EF134L02AE

Reviews:

Related manuals for K-EF134L02AE

Brands by name

Popular brands

Panasonic K-EF134L02AE, Operation Manual

Search results

Summary of Contents for K-EF134L02AE

Reviews:

Related manuals for K-EF134L02AE

Brands by name

Popular brands