Panasonic K-EF134L02AE Operation Manual Download Page 30

Page: 30 / 82

Parameter

Function

Image capture

size

There are multiple resolutions. You can select from

the dropdown list.
For each resolution, the recommended bit stream

value is different.

Frame

rate(FPS)

NTSC: 1-30fps. PAL: 1-25fps
The frame rate may vary due to different resolutions.

Transmission

Priority

There are two options: VBR and CBR.

Please note, you can set video quality in VBR mode.

Reference Bit

Rate

Reference bit rate value according to the resolution

and frame rate you have set.

Bit Rate



In CBR, the bit rate here is the max value. In

dynamic video, system needs to low frame rate

or video quality to guarantee the value.



The value is null in VBR mode.



Please refer to recommend bit rate for the

detailed information.

Refresh

interval

Here you can set the P frame amount between two I

frames. The value ranges from 1 to 150. Default

value is 50.
Recommended value is frame rate.

Summary of Contents for K-EF134L02AE



















































































Search results

Summary of Contents for K-EF134L02AE

Reviews:

Related manuals for K-EF134L02AE

Brands by name

Popular brands

Panasonic K-EF134L02AE, Operation Manual

Search results

Summary of Contents for K-EF134L02AE

Reviews:

Related manuals for K-EF134L02AE

Brands by name

Popular brands