57
RQT8023
Co
n
ven
ie
nt
fu
n
cti
o
n
s
Channel/Clock settings when TV Guide On Screen
TM
system is not used
Refer to the control reference on page 54.
Preparation:
If the television program list has already been downloaded, return the unit to the factory preset condition using the steps indicated below.
When the unit is on and stopped
1
Press and hold [
X
CH] and [
W
CH] on the main unit for about five
seconds.
The unit turns off.
2
Press [
Í
DVD POWER] to turn the unit on.
3
Complete the TV Guide On Screen
TM
system setup (until [ENTER]
is pressed after the “Watch TV” message screen is displayed).
[Note]
You can set scheduled recording only manually after you set the unit with “Set Channels Automatically”.
1
Press [SETUP].
2
Press [
3
,
4
] to select “Channel” and
press [
1
].
3
Press [
3
,
4
] to select “Set Channels
Automatically” and press [ENTER].
4
Press [
2
,
1
] to select “Yes” and
press [ENTER].
5
Press [ENTER].
Auto Channel Setting starts. This takes a few minutes.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished.
≥
DST, Daylight Saving Time, shows the summertime setting.
≥
TIME ZONE shows the time difference from Greenwich
Mean Time (GMT).
EST (Eastern Standard Time)
l
GMT
j
5
CST (Central Standard Time)
l
GMT
j
6
MST (Mountain Standard Time)
l
GMT
j
7
PST (Pacific Standard Time)
l
GMT
j
8
AST (Alaska Standard Time)
l
GMT
j
9
HST (Hawaii Standard Time)
l
GMT
j
10
For other areas: xx hr
≥
If the Auto Clock Setting does not start automatically, select
“Clock Settings” from the “Setup” tab and then select “Set
Clock Automatically”.
≥
If the time was not set correctly, use manual clock setting
(
➡
17) or adjust time zone.
6
Press [ENTER].
≥
The unit configures channels according to the Signal Source
(RF IN) settings as follows.
Adjust the time zone (
j
1 or
i
1) if it was not set correctly with auto
clock setting.
You cannot change this setting if you set the clock manually.
1
Press [SETUP].
2
Press [
3
,
4
] to select “Setup” and
press [
1
].
3
Press [
3
,
4
] to select “Clock
Settings” and press [ENTER].
4
Press [
3
,
4
] to select “Adjust Time
Zone” and press [ENTER].
5
Press [
3
,
4
] to select “
s
1” or “
r
1”
and press [ENTER].
To return to the previous screen
Press [RETURN].
To exit the screen
Press [SETUP].
To cancel partway while Auto Channel/Clock Setting is taking place
Press [RETURN].
I N 2
I N 2
C H
C H
HDD DVD SD
S VIDEO
S VIDEO
VIDEO
VIDEO
L/MONO
L/MONO-AUDIO
AUDIO-R
OPEN/CLOSE
OPEN/CLOSE
DRI
DRIVE
VE
SELECT
SELECT
REC
REC
/x1.3
X
CH
W
Auto channel/clock settings
Channel
SETUP
Setup
Disc
Video
Audio
Set Clock Automatically
Auto Clock Setting is complete.
4/4/2005 12:15 AM
DST.............. On
Time Zone..... CST
Signal Source
(RF IN)
Band
Channel
Antenna
VHF
2–13
UHF
14–69
CableTV
VHF
2–13
CATV LOW BAND
95–99
CATV MID/SUPER BAND
14–36
CATV HYPER BAND
37–65
ULTRA BAND
66–94
100–125
SPECIAL CATV CHANNEL
1
Adjust Time Zone
SETUP
Setup
Disc
Video
Adjust Time Zone
j
1
0
i
1
Channel
EH50English.book Page 57 Tuesday, February 1, 2005 6:36 PM
